ONKYO TX-NR905 Manuale Utente
51
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
less than 6, set the Speaker Impedance to 4 ohms.
To use bi-amping or bridging, you must change the
Speaker Type setting. For hookup information, see pages
27–30.
Speaker Type setting. For hookup information, see pages
27–30.
Notes:
• When bridging is used, the AV receiver is able to drive
up to 2.1 speakers in the main room.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the vol-
ume.
Speaker Settings
The onscreen menus shown in this manual may be
slightly different from what you see on your TV.
slightly different from what you see on your TV.
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “2. Speaker
Setup,” and then press [ENTER].
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
INPUT SELECTOR
DISPLAY
MUTING
GU
IDE
EXI
T
PREV
CH
DIMMER
CDR/MD/DOCK
SAT
TAPE/AMP
SLEEP
MACRO
REMOTE MODE
--/--- 10
11
12
PLAYLIST
RANDOM
D. TUN
CD
TUNER
TAPE
PHONO
REC
ENTER
TO
P M
ENU
MEN
U
VOL
CH
DISC
ALBUM
TV
VCR
CABLE
NET/USB
DVD
RECEIVER
CD
-
1
2
3
ZONE
3
ZONE
2
+
-
+10
0
CLEAR
4
5
6
7
8
9
SE
TUP
RET
UR
N
NET/USB
2, 3
2–5
1
1, 6
If you change these settings, you must run the auto-
matic speaker setup again (see page 61).
matic speaker setup again (see page 61).
RECEIVER
SE
TUP
ENTER
ENTER
3
Use the Up and Down [
]/[
]
buttons to select “1. Speaker Set-
tings,” and then press [ENTER].
tings,” and then press [ENTER].
The Speaker Settings menu appears.
4
Use the Up and Down [
]/[
]
buttons to select “Speaker
Impedance,” and use the Left and
Right [
Impedance,” and use the Left and
Right [
]/[
] buttons to select:
4 ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
speaker is 4 ohms or more but
less than 6.
6 ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
speakers are between 6 and
16 ohms.
5
Use the Up and Down [
]/[
]
buttons to select “Front (Speaker
A),” and use the Left and Right
[
A),” and use the Left and Right
[
]/[
] buttons to select:
Normal:
Select this if you’ve con-
nected your front Speakers A
normally.
nected your front Speakers A
normally.
Bi-Amp:
Select this if you’ve con-
nected your front Speakers A
for bi-amped operation.
nected your front Speakers A
for bi-amped operation.
BTL:
Select this if you’ve con-
nected your front Speakers A
for bridged operation. The
BTL indicator will appear on
the display.
nected your front Speakers A
for bridged operation. The
BTL indicator will appear on
the display.
Note:
• Bi-Amp and BTL cannot be selected
if Front (Speaker B) is set to Bi-Amp
or BTL.
or BTL.
ENTER
ENTER
2-1.Speaker Settings
Speaker Impedance 6ohms
Front(Speaker A) Normal
Front(Speaker B) Not use
Front(Speaker A) Normal
Front(Speaker B) Not use
ENTER
ENTER
TX-NR905_En.book Page 51 Wednesday, January 23, 2008 1:36 PM