ONKYO HT-RC360 Manuale Utente
63
En
Onkyo components that are connected via
u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
Controlling Onkyo components without
u
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
u, use the
following remote control codes:
`
30627:
Onkyo DVD player without
u
`
71817:
Onkyo CD player without
u
`
32900/33100/33500:
Onkyo Blu-ray Disc player
`
32901/33104/33504:
Onkyo HD DVD player
`
70868:
Onkyo MD recorder without
u
`
71323:
Onkyo CD recorder without
u
`
82990:
Onkyo Dock without
u
You can reset a REMOTE MODE to its default remote
control code.
control code.
You can reset the remote controller to its default settings.
By pressing the REMOTE MODE that’s been
programmed with the remote control code for your
component, you can control your component as described
below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(
programmed with the remote control code for your
component, you can control your component as described
below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(
page 62).
Controlling a TV
TV is preprogrammed with the remote control code for
controlling a TV that supports the
controlling a TV that supports the
p
*1
(limited to
some models). The TV must be able to receive remote
control commands via
control commands via
p and be connected to the
AV receiver via HDMI. If controlling your TV via
p doesn’t work very well, program your TV’s
remote control code into TV and use the TV remote mode
to control your TV.
Use the following remote control codes:
p doesn’t work very well, program your TV’s
remote control code into TV and use the TV remote mode
to control your TV.
Use the following remote control codes:
`
11807/13100/13500:
TV with
p
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
DVD Player or DVD Recorder
BD/DVD is preprogrammed with the remote control code
for controlling a component that supports the
for controlling a component that supports the
p
*1
(limited to some models). The component must be able to
receive remote control commands via
receive remote control commands via
p and be
connected to the AV receiver via HDMI.
Use the following remote control codes:
Use the following remote control codes:
`
32910/33101/33501/31612:
Blu-ray Disc/DVD player with
p
*1
The
p
supported by the
AV receiver
is the CEC
system control function of the HDMI standard.
Remote Control Codes for Onkyo
Components Connected via
Components Connected via
u
1
Make sure the Onkyo component is connected with
an
an
u cable and an analog audio cable (RCA).
u Components” for details
page 18).
2
Enter the appropriate remote control code for
REMOTE MODE, referring to the previous
section.
REMOTE MODE, referring to the previous
section.
`
42157:
Onkyo cassette tape deck with
u
`
81993:
Onkyo Dock with
u
3
Press
REMOTE MODE, point the remote
controller at the AV receiver, and operate the
component.
component.
Resetting REMOTE MODE Buttons
1
While holding down
REMOTE MODE that you
want to reset, press and hold down
HOME until the
remote indicator lights (about 3 seconds).
2
Within 30 seconds, press
REMOTE MODE again.
The remote indicator flashes twice, indicating that the
button has been reset.
Each of REMOTE MODE is preprogrammed with a
remote control code. When a button is reset, its
preprogrammed code is restored.
button has been reset.
Each of REMOTE MODE is preprogrammed with a
remote control code. When a button is reset, its
preprogrammed code is restored.
Resetting the Remote Controller
1
While holding down
RECEIVER, press and hold
down
HOME until the remote indicator lights
(about 3 seconds).
2
Within 30 seconds, press
RECEIVER again.
The remote indicator flashes twice, indicating that the
remote controller has been reset.
remote controller has been reset.
Controlling Other Components