Manualsbrain.com
  1. Manuali
  2. Marche
  3. Marantz
  4. SR4400
  5. Manuale Utente

Marantz SR4400 Manuale Utente

Scarica
Pagina di 36
11
ENGLISH
DIGITAL
DIGITAL
IN
IN
OUT
OUT
DIG-1 IN
DIG-1 IN
DIG-2 IN
DIG-2 IN
DIG.OUT
DIG.OUT
OPT
OPT
DIG-4 IN
DIG-4 IN
DIG-3 IN
DIG-3 IN
DIG.OUT
DIG.OUT
COAX
COAX
SURROUND
SURROUND
BACK
BACK
R
R
SURROUND
SURROUND
L
L
L
L
FRONT
FRONT
CENTER
CENTER
R
R
VIDEO
VIDEO
S-VIDEO
S-VIDEO
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
IN
IN
IN
IN
OUT
OUT
DSS
DSS  //  VCR2
VCR2
VCR1
VCR1
DVD
DVD
AUDIO
AUDIO
TV
TV
TAPE
TAPE
CD
CD
CDR
CDR  //  MD
MD
SUB
SUB
WOOFER
WOOFER
CENTER
CENTER
CE
CENTER
FRONT
FRONT
FRONT
SURROUND
SU
SURR.
B
BACK
SURROUND
SURROUND
SUB
SUB
WOOFER
WOOFER
SURR.
SURR.
BACK
BACK
6.1CH INPUT
6.1CH INPUT
L
R
IN
IN
MONITOR
MONITOR
OUT
OUT
VCR1 OUT
VCR1 OUT
VCR1 IN
VCR1 IN
DVD IN
DVD IN
L
L
R
R
IN
IN
IN
IN
OUT
OUT
OUT
OUT
PRE OUT
OUT
OUT
MONITOR
MONITOR
IN
IN
TV
TV
DSS
DSS  //  VCR2
VCR2
DVD
DVD
VCR1
VCR1
IN
IN
GND
GND
AM
AM
FM
FM
ANTENNA
ANTENNA
((75
75
Ω
Ω
))
REMOTE
REMOTE
CONTROL
CONTROL
SWITCHED  100W MAX
SWITCHED  100W MAX
SPEAKER SYSTEMS
SPEAKER SYSTEMS
AC OUTLET
AC OUTLET
DIGITAL
DIGITAL
DIG-1 IN
DIG-1 IN
DIG.OUT
DIG.OUT
OPT
OPT
DIG-4 IN
DIG-4 IN
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
AUDIO
AUDIO
TAPE
TAPE
CD
CD
CDR
CDR  //  MD
MD
L
L
R
R
OUT  IN
L
R
L
R
OUT
L
R
L R
L R
L R
R
L
L
R
R
L
OUT  IN
L
R
L
R
DIGITAL
OUTPUT
DIGITAL
OUTPUT
DIGITAL
INPUT
R L
L R
L R
R
L
L
R
ANALOG AUDIO
DIGITAL AUDIO
(COAXIAL)
DIGITAL AUDIO
(OPTICAL)
CONNECTING AUDIO COMPONENTS
The output audio signal from the TAPE OUT jack
and the CD-R/MD OUT jack is the sound source
currently selected.
Caution:
• Do not connect this unit and other components to
mains power until all connections between
components have been completed.
Notes:
• Insert all plugs and connectors securely.
Incomplete connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R(right) channel, and
white connectors are for the L(left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that
is connected with this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables will result in
generating hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are four digital inputs, two coaxial jacks
and two optical jacks, on the rear panel. You can
use these jacks to input PCM, Dolby Digital and
DTS bitstream signals from a CD, DVD, or other
digital source components.
• There are one digital output with coaxial jack
and one with optical jack on the rear panel.
These jacks can be connected to CD recorder,
MD deck.
• Setup the digital audio format of DVD player, or
other digital source component. Refer to the
i n s t r u c t i o n s   f o r   e a c h   c o m p o n e n t   t o   b e
connected to digital input jacks.
• Use fiber optical cables(optical) for DIG-1,2
input jacks.  Use 75 ohms coaxial cables(for
digital audio or video) for DIG-3,4 input jacks.
• You can designate the input for each digital
input/output jacks according to your component.
See page 16.
Notes:
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to the
EIA standard.  If you use a cable that does not
conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
1.
2.
3.
4.
5.
CONNECTING SPEAKER WIRE
1.
Strip away approx. 10 mm of wire insulation.
2.
Twist the bared wire ends tight to prevent
short circuits.
3.
Loosen the knob by turning counterclockwise.
4.
Insert the bare part of the wire into the hole in
the side of each terminal.
5.
Tighten the knob by turning clockwise to
secure the wire.
Cautions:
• Be sure to use speakers with the specified
impedance shown on the rear panel of this unit.
• To prevent damage
to circuitry, do not
let the bare speaker
w i r e s   t o u c h   e a c h
other and do not let
them touch any metal
part of this unit.
• Do not touch the speaker terminals when the
power is on.  It may cause electric shocks.
• Do not connect more than one speaker cable to
one speaker terminal. Doing so may damage this
unit.
Note:
• Be sure to connect the positive and negative
cables for the speaker properly. If they are miss-
connected, the signal phase will reversed and the
signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect
a powered subwoofer (power amplifier built in ).
If your subwoofer is passive type (power amplifier
is not built in), connect a monaural power amplifier
to the PRE OUT SUBWOOFER jack and connect
the subwoofer to the amplifier.
3/8 inch
(10 mm)
CD RECORDER / MD DECK
CD PLAYER
TAPE DECK
SR4400U DFU_01_ENG 1_2
03.4.10, 3:00 PM
Page 11
Adobe PageMaker 6.5J/PPC