Pioneer VSX-919AH-S Manuale Utente
Additional information
12
106
En
Settings
Symptom
Remedy
The Auto MCACC Setup
continually shows an error.
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as
low as possible (see also Problems when using the Auto MCACC Setup on
page 40). If the noise level cannot be kept low enough, you will have to set up
the surround sound manually (page 93).
• When using only one surround back speaker, connect it to the SURROUND
BACK L (Single) terminals.
• To use a 5.1-channel speaker set, use the surround speakers for the surround
channel, not the surround back channel.
• Make sure there are no obstacles between the speakers and the microphone.
• If Reverse Phase is displayed, try the following:
– The speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
– Depending on the type of speakers and their installation conditions, Reverse
Phase may be displayed even if the speakers are properly connected. If this
happens, select GO NEXT and continue.
– If the speaker is not pointed to the microphone (listening position) or when
using speakers that affect the phase (dipole speakers, reflective speakers, etc.),
it may not be possible to properly identify the polarity.
low as possible (see also Problems when using the Auto MCACC Setup on
page 40). If the noise level cannot be kept low enough, you will have to set up
the surround sound manually (page 93).
• When using only one surround back speaker, connect it to the SURROUND
BACK L (Single) terminals.
• To use a 5.1-channel speaker set, use the surround speakers for the surround
channel, not the surround back channel.
• Make sure there are no obstacles between the speakers and the microphone.
• If Reverse Phase is displayed, try the following:
– The speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
– Depending on the type of speakers and their installation conditions, Reverse
Phase may be displayed even if the speakers are properly connected. If this
happens, select GO NEXT and continue.
– If the speaker is not pointed to the microphone (listening position) or when
using speakers that affect the phase (dipole speakers, reflective speakers, etc.),
it may not be possible to properly identify the polarity.
After using the Auto MCACC
Setup, the speaker size
setting is incorrect.
Setup, the speaker size
setting is incorrect.
• There may have been some low frequency noise in the room from an air-
conditioner, motor, etc. Switch off all other appliances in the room and use
Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this
may occur in some cases. Change the speaker setting manually in Speaker
Setting on page 94, and use the ALL (Keep SP System) option for the Auto
MCACC menu in Automatic MCACC (Expert) on page 77 if this is a recurring
problem.
conditioner, motor, etc. Switch off all other appliances in the room and use
Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this
may occur in some cases. Change the speaker setting manually in Speaker
Setting on page 94, and use the ALL (Keep SP System) option for the Auto
MCACC menu in Automatic MCACC (Expert) on page 77 if this is a recurring
problem.
Can’t adjust the Fine Speaker
Distance setting (page 82)
properly.
Distance setting (page 82)
properly.
• Check that the speakers are all in phase (make sure the positive (+) and
negative (–) terminals are matched up properly).
negative (–) terminals are matched up properly).
The display shows KEY LOCK
ON when you try to make
settings.
ON when you try to make
settings.
• With the receiver in standby, press
STANDBY/ON while holding down
SPEAKERS to disable the key lock.
Most recent settings have
been erased.
been erased.
• The power cord was disconnected from the wall while adjusting this setting.
• Settings are only stored if all the zones are turned off. Turn off all the zones
before unplugging the power cord.
• Settings are only stored if all the zones are turned off. Turn off all the zones
before unplugging the power cord.
VSX-1019_DF.book 106 ページ ２００９年３月１３日 金曜日 午前９時５８分