Manualsbrain.com
  1. Manuali
  2. Marche
  3. Kenwood
  4. KAC-X542
  5. Manuale Utente

Kenwood KAC-X542 Manuale Utente

Scarica
Pagina di 28
English
  3
B ch
A ch
INPUT
SENSITIVITY(V)
INPUT
SENSITIVITY(V)
HPF
FREQUENCY(Hz)
HPF
FREQUENCY(Hz)
LPF
FREQUENCY(Hz)
4
0.2(MAX)
(MIN)5
3
2
1
0.5
0.3
4
0.2(MAX)
(MIN)5
3
2
1
0.5
0.3
50
200
50
200
150
100
70
50
200
150
100
70
150
100
70
FILTER
HPF
LPF
OFF
AMP CONT
ON
OFF
ISF
ON
OFF
HPF
ON
OFF
OPERATION
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
HPF OPERATION
LPF OPERATION
50 Hz
70 Hz
100 Hz
150 Hz
200 Hz
30
-20
-16
-12
-8
-4
0
50 100 200 400
1K (Hz)
30
-20
-16
-12
-8
-4
0
50 100 200 400
1K (Hz)
4/3/2channel Power Amplifier
VOLT
FAN
CURR
TEMP
446 mm
432 mm
Ø6
157
m
m
252
m
m
265
m
m
Installation
Accessories
Part name
External View
Number of Items
Self-tapping screws 
(ø5 × 18 mm)
4
Hexagon socket head cap screw 
(M4 × 8 mm)
4
Cover 
1
Terminal cover (Power terminal)
1
Hexagon Wrench
1
Installation procedure
Since there are large variety of settings and connections possible according to 
applications, read the instruction manual well to select the proper setting and 
connection.
1.  Remove the ignition key and disconnect the negative 
- terminal of the 
battery to prevent short circuits. 
2.  Set the unit according to the intended usage.
3.  Connect the input and output wires of the units.
4.  Connect the speaker wires.
5.  Connect the power wire, power control wire and grounding wire following 
this order.
6.  Install the installation fittings in the unit.
7.  Attach the unit.
8.  Install the terminal cover.
9.  Connect the negative 
- terminal of the battery.
2 CAUTION
•  Do not install in the below locations;
(Unstable location, In a location that interferes with driving, In a location 
that gets wet, In a dusty location, In a place that gets hot, In a place that 
gets direct sunlight, In a location that gets hit by hot air)
•  Do not install the unit under the carpet. Otherwise heat build-up occurs 
and the unit may be damaged.
•  Install this unit in a location which allows heat to easily dissipate.
Once installed, do not place any object on top of the unit.
•  The surface temperature of the amplifier will become hot during use. Install 
the amplifier in a place where people, resins, and other substances that are 
sensitive to heat will not come into contact with it.
•  This unit has cooling fans to decrease the internal temperature. Do not 
mount the unit in a place where the cooling fan and ducts of the unit are 
blocked. Blocking these openings will inhibit the cooling of the internal 
temperature and result in malfunction.
•  When making a hole under a seat, inside the trunk, or somewhere else in 
the vehicle, check that there is nothing hazardous on the opposite side 
such as a gasoline tank, brake pipe, or wiring harness, and be careful not to 
cause scratches or other damage.
•  Do not install near the dashboard, rear tray, or air bag safety parts.
•  The installation to the vehicle should securely fasten the unit to a place in 
which it will not obstruct driving. If the unit comes off due to a shock and 
hits a person or safety part, it may cause injury or an accident.
•  After installing the unit, check to make sure that electrical equipment 
such as the brake lamps, turn signal lamps and windshield wipers operate 
normally.
Installation board, etc.
(thickness : 15 mm or more)
Self-tapping screw
(ø5 × 18 mm)
Cooling fan
Hexagon socket 
head cap screw 
(M4 × 8 mm)
Hexagon Wrench
Cover 
Cooling fan
Duct
B64-3395-00_00.indb   3
B64-3395-00_00.indb   3
05.11.18   9:15:13 AM
05.11.18   9:15:13 AM