Ashly 800 Dépliant

The power amplifiers shall consist of six separate models (800, 

1200, 1800, 2400, 3000, and 3800), being of two channels, and 

shall deliver a minimum power ranging from 200 to 1100 watts 

RMS per channel into 8 ohm loads and ranging from 400 to 1900 

watts RMS per channel into 4 ohms depending on the model 

being used. When switched into Bridged-Mono mode, the ampli-

fier in use shall deliver a range from 800 to 3800 watts RMS into 

8 ohms. All amplifiers shall have the ability for input attenua-

tion, channel mute, channel polarity, input level, output voltage, 

output current, clipping, temperature, and power on/off be con-

trolled or monitored through the standard, built-in Ethernet port 

using Proteane Software™.

The amplifiers shall have the capability to replace the input mod-

ule with either a 32 bit/96kHz, Proteane DSP module featuring 

both analog and digital (AES3) inputs, two additional processed 

output channels and extensive digital signal processing or the 

PNE-C2 CobraNet module.

Dimensions of the amplifiers shall be 19”W x 3.5”H x 15.5”D, 

with a weight range of 22 to 24 pounds. The amplifiers shall uti-

lize a state-of-the-art, efficient, two-stage high speed switched 

mode power supply. Cooling shall be accomplished by the use 

of a temperature sensitive variable speed fan with front to back 

airflow.

 

The amplifier shall have a selectable input gain of 26dB, 32dB 

or 1.4V. Frequency response shall be 20 Hz - 20 kHz, +/- 0.15 

dB.  Hum and noise shall range from >98dB to 112dB below full 

output (20Hz to 20KHz A-weighted) and SMPTE intermodulation 

distortion shall be <.01% (8 ohm load, 10dB below rated power). 

Total Harmonic Distortion (20Hz - 20KHz at 8 ohms) shall be 

<.01% (8 ohm load, 10dB below rated power, 20Hz-10 kHz). 

Each amplifier channel shall be supplied with a calibrated stepped 

input attenuator located on the front panel with the capability of 

the attenuators to be disabled. Each pair of inputs shall have a 

selectable, bypassable high pass filter of 12dB/octave at 30Hz 

and 50Hz, a switch to select stereo or mono mode and a switch 

to select dual or bridge mode. There shall be an input ground 

switch located on the rear panel to select chassis or floating 

ground operation and a selectable clip limiter with off, slow, and 

fast settings.

The inputs shall be active balanced design, with an impedance 

of 20K ohm with a maximum input level of +21dBu. Input con-

nections shall be XLR-1/4” Neutrik combo connectors and 6-pin 

Euroblock. XLR male connectors shall be provided for looping to 

additional amplifiers. Output connectors shall be locking Neutrik 

Speakon. Models 800 and 1200 shall have a 4 position screw ter-

minal strip with safety cover as an additional output.

The amplifiers shall have front panel indicators for power, stand-

by, protect, bridged mono, parallel mono, and data communica-

tions. Each channel shall have signal indicators for clip, -6 dB, 

-12 dB, -18 dB levels, temp, output current. 

The amplifier shall have built in protection for inrush current, 

temperature, output DC, SOA of power transistors, output over-

current and mains power.

The amplifiers shall be capable of operation by means of its own 

built-in power supply connected to 110 - 125VAC, 220 - 250VAC, 

50/60Hz.

The amplifier shall be covered under a full limited warranty of not 

less than five years. The amplifier shall be a PE-Series model, 

manufactured by Ashly Audio, Inc. of Rochester, New York.

Features

• Ethernet Remote Control & 

Monitoring

• 2-Stage High Efficiency Switched 

Mode Power Supply

• Calibrated, Stepped Input 

Attenuators 

• Input Sensitivity 26dB, 36db or 1.4V
• DC Voltage Control of Input & 

Remote Power Turn-On/Off

• Temperature Sensitive Variable 

Speed Fan Front to Back Airflow

• Selectable Subsonic Filter 
• Selectable Clip-Limiter
• 4-Stage Level Meters
• Amplifier Status Indicators:

Power, Standby, Bridge Mono, 

Parallel Mono, Protect and 
Communications Enabled

• Output Current & Temp Indicators
• Safety/Compliance: cTUVus/FCC, 

CE, RoHS

Technical Notes & Specifications

PE-Series  Ethernet Controlled, Two-Channel Amplifiers