JVC FS-SD7R Manuale Utente
G-1
Warnings, Cautions and Others
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appro-
priate safety approved extension lead or consult your dealer.
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appro-
priate safety approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical approved
type, as originally fitted.
type, as originally fitted.
If nontheless the mains plug is cut off ensure to remove the fuse
and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow
the instructions given below:
the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
accordance with the following code:
Blue :Neutral
Brown :Live
As these colours may not correspond with the coloured mark-
ings identifying the terminals in your plug proceed as follows:
ings identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the termi-
nal which is marked with the letter N or coloured black.
nal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the ter-
minal which is marked with the letter L or coloured red.
minal which is marked with the letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Caution —
switch!
Disconnect the mains plug to shut the power off completely.
The
The
switch in any position does not disconnect the mains
line. The power can be remote controlled.
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
1
CLASSIFICATION LABEL, PLACED ON EXTERIOR SUR-
FACE
FACE
2
WARNING LABEL, PLACED INSIDE THE UNIT
1
CLASS 1 LASER PRODUCT
2
DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
failed or defeated. Avoid direct exposure to beam.
3
CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to qual-
ified service personnel.
serviceable parts inside the Unit; leave all servicing to qual-
ified service personnel.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
To reduce the risk of electrical shocks, fire, etc.:
1
Do not remove screws, covers or cabinet.
2
Do not expose this appliance to rain or moisture.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
3
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
3
Front:
No obstructions and open spacing.
4
Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
5
Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height
of 10 cm or more.
of 10 cm or more.
CAUTION
■
■
■
■
About the Internal Cooling Fan
This unit includes an internal cooling fan, so as to allow for high-power operation within a small space.
This fan comes on when the sound level is set high, and may also come on even at low sound levels if the internal temperature rises. To ensure
effective fan operation, please leave at least 15cm clearance between the rear of the unit and the wall, and at least 1cm clearance on each side of
the unit.
This unit includes an internal cooling fan, so as to allow for high-power operation within a small space.
This fan comes on when the sound level is set high, and may also come on even at low sound levels if the internal temperature rises. To ensure
effective fan operation, please leave at least 15cm clearance between the rear of the unit and the wall, and at least 1cm clearance on each side of
the unit.
CLASS 1
LASER PRODUCT
Front view
Side view
10 cm
15 cm
15 cm
15 cm
1 cm
1 cm
STANDBY/ON
OPEN/CLOSE
PHONES
15 cm
15 cm
FS-SD5(B).book Page 1 Tuesday, February 15, 2000 1:13 PM