ONKYO CR-545 CR-545UKD Manuale Utente
Troubleshooting
47
If you have any trouble using the CD receiver, look for a solution in this section.
Power
Can’t turn on the CD receiver.
• Make sure that the power cord is properly plugged into the wall outlet (see page 17).
• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
• Make sure that the power cord is properly plugged into the wall outlet (see page 17).
• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
The CD receiver turns off unexpectedly.
• If the sleep timer has been set and the TIMER indicator is shown on the display, the CD receiver will turn off
• If the sleep timer has been set and the TIMER indicator is shown on the display, the CD receiver will turn off
automatically after a specified period.
• When timed playback finishes, the CD receiver automatically switches to Standby mode.
• If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can
• If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can
happen if there’s a short between the positive and negative wires of a speaker cable.
Audio
There’s no sound.
• Make sure the CD receiver’s volume control is not set to minimum (see page 18).
• Make sure the correct input source is selected (see page 18).
• Make sure the CD receiver is not muted (see page 18).
• Make sure the speakers are connected correctly (see page 15).
• Check all connections and correct as necessary (see pages 13 to 17).
• While headphones are connected, the speakers output no sound (see page 18).
• Make sure the CD receiver’s volume control is not set to minimum (see page 18).
• Make sure the correct input source is selected (see page 18).
• Make sure the CD receiver is not muted (see page 18).
• Make sure the speakers are connected correctly (see page 15).
• Check all connections and correct as necessary (see pages 13 to 17).
• While headphones are connected, the speakers output no sound (see page 18).
The sound quality is not good.
• Make sure the speaker cables are connected with the correct polarity (see page 15).
• Make sure all audio connecting plugs are pushed in all the way (see page 16 to 17).
• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such
• Make sure the speaker cables are connected with the correct polarity (see page 15).
• Make sure all audio connecting plugs are pushed in all the way (see page 16 to 17).
• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such
devices away from the CD receiver.
• If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone
that’s being used to make a call, the CD receiver may output noise.
• The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during
playback or when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
Headphone output is intermittent or there’s no sound.
• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for
• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for
cleaning information. Also, make sure that the headphones cable is not broken or damaged.
• When you select iPod as the input source, the headphones output no sound.
Audio performance
• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and
• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and
had time to warm up.
• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t
do it.
How to reset to factory default?
1. Before unplug the power-supply co
RD, set the CD receiver in the STANDBY state.
2. While holding down the [ON/STANDBY] button on the main unit, plug the power-supply
co
RD.
"RESET" appears on the display, then the CD receiver is in the STANDBY state.