ONKYO TX-SR602 Guida Al Funzionamento
88
Controlling Other Components
—Continued
The AV receiver’s remote controller can learn the com-
mands of other remote controllers simply by pointing
them at each other. For example, by transmitting the Play
command from your CD player’s remote controller, the
remote controller can learn it and then transmit the same
command when its Play [
mands of other remote controllers simply by pointing
them at each other. For example, by transmitting the Play
command from your CD player’s remote controller, the
remote controller can learn it and then transmit the same
command when its Play [
] button is pressed in CD
mode.
This is convenient when you want to add commands to
buttons after entering a remote control code (page 80).
This is convenient when you want to add commands to
buttons after entering a remote control code (page 80).
Notes:
• The following buttons cannot be taught new com-
mands: REMOTE MODE, MACRO [1], [2], [3], TV
[
[
], TV [INPUT], TV CH [+]/[–], TV VOL [
]/
[
].
• The AV receiver’s remote controller can learn up to
approximately 150 commands. However, the com-
mands of some remote controllers may use a lot of
memory, in which case, this will be reduced.
mands of some remote controllers may use a lot of
memory, in which case, this will be reduced.
• By default, the AV receiver’s remote controller knows
the commands for controlling an Onkyo CD player,
cassette deck, DVD player, and MD player (e.g., Play,
Stop, Pause, etc., buttons). These buttons can learn
new commands, although the defaults will be restored
if the remote controller is reset.
cassette deck, DVD player, and MD player (e.g., Play,
Stop, Pause, etc., buttons). These buttons can learn
new commands, although the defaults will be restored
if the remote controller is reset.
• To learn a new command for a button that has already
learned one, simply repeat this procedure.
• Like most remote controllers, the AV receiver’s
remote controller uses infrared. Commands from
remote controllers that don’t use infrared cannot be
learnt.
remote controllers that don’t use infrared cannot be
learnt.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
learned all over again, so don’t discard your other
remote controllers.
Learning Commands from Another
Remote Controller
Remote Controller
1
While holding down the REMOTE
MODE button that you want to
learn the command, press the
[ON] button.
MODE button that you want to
learn the command, press the
[ON] button.
2
On the AV receiver’s remote con-
troller, press the button you want
to learn the new command.
troller, press the button you want
to learn the new command.
1
1, 4
ON
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then, on the
other remote controller, press the
button whose command you
want to learn.
each other, about 2 to 6 inches
(5–15 cm) apart, and then, on the
other remote controller, press the
button whose command you
want to learn.
4
To teach the AV receiver’s remote
controller more new commands,
repeat steps 2 and 3.
controller more new commands,
repeat steps 2 and 3.
Press the [ON] button when you’ve fin-
ished.
ished.
PO
W
ER
SLE
EP
D
IM
M
ER
SU
R
M
O
D
E
VID
EO-
1
VID
EO
-2
TA
PE
D
VD
C D
C
D
DV
D
TU
N
ER
TU
N
ER
PH
O
N
O
IN
PU
T S
ELE
C
TO
R
DISC
TA
PE
VO
LU
M
E
LE
VE
L
C
H
SE
L
PR
ES
ET
M
U
TI
NG
TE
ST
TO
N
E
MU
LT
I-C
H
IN
PUT
G
R
O
U
P
R
ON
ST
AND
BY
TV
TV
CH
TV
VO
L
--
/---
SLE
EP
IN
PU
T
I
SA
T
CA
BL
E
DVD
CD
+1
0
0
CLE
AR
1
2
3
4
5
6
7
8
9
+
-
M
ACRO
1
2
3
MD
/CD
R
INPUT
SELEC
TOR
V1
V2
V3
CD
TAPE
V4
DVD
MU
LTI C
H
TU
NER
RE
M
O
TE
M
O
DE
About 2 to 6
inches (5–15 cm
inches (5–15 cm
RC-588M
TX-NR702,602_En.book Page 88 Tuesday, September 7, 2004 1:18 PM