Zenoah BCZ3200DL Manuale Utente
GB-15
G
B
BCZ3200DL / BCZ3200DW
IMPORTANT
• If waste gets stuck and causes blockage around the
intake air cooling vent or between the cylinder fins, it
may cause the engine to overheat, and that in turn
may cause mechanical failure on the part of the
brushcutter.
may cause the engine to overheat, and that in turn
may cause mechanical failure on the part of the
brushcutter.
PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE
EVERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver into the vent,
and wipe away any carbon buildup. Wipe away any
carbon buildup on the muffler exhaust vent and cylin-
der exhaust port at the same time.
carbon buildup on the muffler exhaust vent and cylin-
der exhaust port at the same time.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked its way
3. Check to see if any oil or grease has worked its way
in between the clutch lining and drum, and if it has,
wipe it away using oil-free, lead-free gasoline.
wipe it away using oil-free, lead-free gasoline.
MUFFLER
WARNING
• Inspect periodically, the muffler for loose fasteners,
any damage or corrosion. If any sign of exhaust leak-
age is found, stop using the machine and have it re-
paired immediately.
age is found, stop using the machine and have it re-
paired immediately.
• Note that failing to do so may result in the engine
catching on fire.
SPARK ARRESTER
• The muffler is equipped with a spark arrester to prevent
• The muffler is equipped with a spark arrester to prevent
red hot carbon from flying out of the exhaust outlet. Peri-
odically inspect and clean as necessary with a wire brush.
odically inspect and clean as necessary with a wire brush.
(1)Spark arrester
ANGLE TRANSMISSION
• The reduction gears are lubricated by multipurpose,
• The reduction gears are lubricated by multipurpose,
lithium-based grease in the angle transmission. Sup-
ply new grease every 25 hours of use or more often
depending on the job condition.
ply new grease every 25 hours of use or more often
depending on the job condition.
• Remove the bolt opposit to the grease nipple before
installing new grease to arrange for old grease to exit.
INTAKE AIR COOLING VENT
WARNING
• Never touch the cylinder, muffler, or spark plugs with
your bare hands immediately after stopping the en-
gine. The engine can become very hot when in op-
eration, and doing so could result in severe burns.
gine. The engine can become very hot when in op-
eration, and doing so could result in severe burns.
• When checking the machine to make sure that it is
okay before using it, check the area around the muf-
fler and remove any wood chips or leaves which have
attached themselves to the brushcutter. Failing to do
so could cause the muffler to become overheated and
that in turn could cause the engine to catch on fire.
Always make sure that the muffler is clean and free
of wood chips, leaves, and other waste before use.
fler and remove any wood chips or leaves which have
attached themselves to the brushcutter. Failing to do
so could cause the muffler to become overheated and
that in turn could cause the engine to catch on fire.
Always make sure that the muffler is clean and free
of wood chips, leaves, and other waste before use.
•
Check the intake air cooling vent and the area around
the cylinder cooling fins after every 25 hours of use
for blockage, and remove any waste which has at-
tached itself to the brushcutter. Note that it is nec-
essary to remove the engine cover shown in in or-
der to be able to view the upper part of the cylinder.
the cylinder cooling fins after every 25 hours of use
for blockage, and remove any waste which has at-
tached itself to the brushcutter. Note that it is nec-
essary to remove the engine cover shown in in or-
der to be able to view the upper part of the cylinder.
10. Storage
Aged fuel is one of major causes of engine starting fail-
ure. Before storing the unit, empty the fuel tank and run
the engine until it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking necessary
measures for rust prevention.
ure. Before storing the unit, empty the fuel tank and run
the engine until it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking necessary
measures for rust prevention.
9. Maintenance
(1)
(1) Cylinder
(2) Intake air cooling vent
(2) Intake air cooling vent
11. Disposal
When disposing your machine, fuel or oil for the machine,
be sure to allow your local regulations.
be sure to allow your local regulations.