Zenoah BK3420FL-EZ Manuale Utente

Pagina di 40
36
English
7. MAINTENANCE 
■ MAINTENANCE BEFORE LONG-
TERM STORAGE
This machine is highly
inflammable.
• When you take fuel out, keep
the fuel tank well away from
flames.
• Be careful not to spill the fuel,
and completely wipe off all fuel
spills.
• If you will not use the machine for
a long time (two months or more),
take out the fuel from the fuel tank
and carburetor. If you leave the
fuel tank and carburetor filled with
fuel for a long time, the fuel might
deteriorate and clog the inside of
the carburetor, thus causing
engine problems (such as wrong
start or insufficient output).
• When storing the machine for a
long time, loosen the cap of the
fuel tank slightly. Excessive
tightening of the cap might deform
its packing over time.
1. Brush off dirt from the machine,
and check the damage or slack of
each part. If you find any abnormal
part, repair it completely ready for
the next time the machine is used.
2. Extract fuel from the fuel tank,
switch on the engine, and leave it
running until it stops naturally.
3. Remove the spark plug, and pour
1 to 2 ml of 2-cycle oil into the
engine. Draw the starter rope two
to three times, set the plug back,
and stop it at the contraction
position.
4. Supply some grease to the gear
case, and apply anti-rust oil to the
metal parts such as the throttle
wire.
5. Apply a little oil to the blade, put
the cover on the blade, and keep
the machine in a safe place away
from heat and humidity.
(1) Tank cap
(2) Fuel tank
IMPORTANT
WARNING
■장기 보관시의 손질
인화로 인한 화재의 위험이 있습니다.
●연료를 빼어 낼 때에는 화기를 멀리
해 주십시오.
●연료를 흘리지 않도록 주의하고, 흘
린 연료는 완전히 닦아 주십시오.
●장기간(2개월 이상) 사용하지 않을 
경우,  연료탱크와  캬뷰레터로부터 
연료를 뽑아 주십시오. 연료는 넣은 
상태로 장기간 방치하면, 연료가 변
질되어 캬뷰레터 내부가 막히고, 엔
진고장(시동불량이나  출력부족)의 
원인이 됩니다.
●보관시에는,  연료탱크의  뚜껑을  느
슨하게  해  주십시오.  너무  강하게 
조이면 경시변화에 의해 패킹이 변
형할 수 있습니다.
1.기계  본체의  오염을  제거하면서, 
각 부의 손상이나 느슨함의 유무를 
점검하고, 이상이 발견된 곳은 다음
번 사용에 대비해서 완전하게 정비
해 주십시오.
2.연료  탱크로부터  연료를  뽑아  낸 
후, 엔진을 걸어 자연적으로 정지할 
때까지 운전해 주십시오.
3.스파크 플러그를 빼어 내고, 2사이
클 오일을 1~2cc엔진 내부에 넣어 
주십시오.
스타터 로브를 2~3회 당긴 후, 플러
그를  원상태로  조립하고  압축위치
에서 정지해 주십시오.
4.스로틀 와이어 등의 금속부에 방청
유를  바른  후,  칼날에  커버를  씌우
고,  실내의  화기나  습기가  없는  장
소에 시트 등을 덮어서 보관해 주십
시오.
5.플랙시블  샤프트는  가능하면  똑바
로 직선으로 하여 보관해 주십시오.
(1)뚜껑
(2)연료탱크
MA12