Zenoah BC4350FW Manuale Utente
■ PROCEDURES TO BE PERFORMED
AFTER EVERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver into
the vent, and wipe away any carbon buildup.
Wipe away any carbon buildup on the
muffler exhaust vent and cylinder exhaust
port at the same time.
Wipe away any carbon buildup on the
muffler exhaust vent and cylinder exhaust
port at the same time.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked
3. Check to see if any oil or grease has worked
its way in between the clutch lining and
drum, and if it has, wipe it away using oil-
free, lead-free gasoline.
drum, and if it has, wipe it away using oil-
free, lead-free gasoline.
■ MAINTENANCE BEFORE STORAGE
• Old fuel left in the carburetor may cause
• Old fuel left in the carburetor may cause
starting failure. When a series of operation
finished, make sure to empty the fuel tank
and drain the carburetor.
finished, make sure to empty the fuel tank
and drain the carburetor.
• Check all parts and the functions. If the
failured or damaged parts have been found,
replace them with new ones.
replace them with new ones.
■ GEAR CASE
• The reduction gears are lubricated by
• The reduction gears are lubricated by
multipurpose, lithium-based grease in the
gear case. Supply new grease every 25
hours of use or more often depending on the
job condition.
gear case. Supply new grease every 25
hours of use or more often depending on the
job condition.
• Remove the bolt opposit to the grease nipple
before installing new grease to arrange for
old grease to exit.
old grease to exit.
■ INTAKE AIR COOLING VENT
• Never touch the cylinder, muffler, or
spark plugs with your bare hands
immediately after stopping the engine.
The engine can become very hot when in
operation, and doing so could result in
severe burns.
immediately after stopping the engine.
The engine can become very hot when in
operation, and doing so could result in
severe burns.
• When checking the machine to make sure
that it is okay before using it, check the
area around the muffler and remove any
wood chips or leaves which have
attached themselves to the brushcutter.
Failing to do so could cause the muffler
to become overheated and that in turn
could cause the engine to catch on fire.
Always make sure that the muffler is
clean and free of wood chips, leaves, and
other waste before use.
area around the muffler and remove any
wood chips or leaves which have
attached themselves to the brushcutter.
Failing to do so could cause the muffler
to become overheated and that in turn
could cause the engine to catch on fire.
Always make sure that the muffler is
clean and free of wood chips, leaves, and
other waste before use.
WARNING
Specifications
7
MODEL CODE
Unit
BC4350FW
Overall size
Length
mm
1845
Width
mm
650
Height
mm
560
Dry weight
Kg
7.8
Engine model
✽
G45L-F
Displacement
cc
41.5
Carburetor
✽
Float
Fuel (Mixture ratio)
✽
50:1 (Gasoline and 2cycle oil)
Fuel tank capacity
litter
0.8
Service range
rpm
5000~8000
Spark plug
✽
Champion RCJ6Y
Clutch system
✽
Two-shoe Centrifugal-Type
Anti-vibration system
Housing
✽
Yes
Handle-bracket
✽
No
Gearhead
Neck angle
deg
60
Reduction ratio
✽
1.400
Blade rotation
✽
Counter-clockwise
Handle type
✽
Double
Throttle lever
✽
Trigger Type (With Safety-lock)
Standard cutter
✽
2 Teeth Blade
Harness type
✽
Double
Quick release
✽
Yes
Standard accessories
Fuel-Tank
✽
●
Tool-kit
✽
●
Owner's manual
✽
●
Specifications are subject to change without notice.
• Check the intake air cooling vent and the
area around the cylinder cooling fins after
every 25 hours of use for blockage, and
remove any waste which has attached
itself to the brushcutter. Note that it is
necessary to remove the engine cover
shown in in order to be able to view the
upper part of the cylinder.
every 25 hours of use for blockage, and
remove any waste which has attached
itself to the brushcutter. Note that it is
necessary to remove the engine cover
shown in in order to be able to view the
upper part of the cylinder.
If waste gets stuck and causes blockage
around the intake air cooling vent or between
the cylinder fins, it may cause the engine to
overheat, and that in turn may cause
mechanical failure on the part of the
brushcutter.
around the intake air cooling vent or between
the cylinder fins, it may cause the engine to
overheat, and that in turn may cause
mechanical failure on the part of the
brushcutter.
(1) Cylinder
(2) Intake air cooling vent
(2) Intake air cooling vent
■ IMUFFLER
• Inspect periodically, the muffler for loose
fasteners, any damage or corrosion. If
any sign of exhaust leakage is found,
stop using the machine and have it
repaired immediately.
any sign of exhaust leakage is found,
stop using the machine and have it
repaired immediately.
• Note that failing to do so may result in the
engine catching on fire.
WARNING
IMPORTANT