Land Pride RCB6610 Manuale Utente

11/11/12

The jack mount angle should be adjusted to position the 
park jack vertical while supporting the cutter hitch. This 
angle will vary depending on the number and size of 
stroke control spacers placed on the lift cylinder rod.

1.

With cutter hitched to a tractor, lower cutter to storage 
height.

2.

Shut tractor down properly before dismounting. Refer 
to “Tractor Shutdown Procedure” on page 14.

3.

Install park jack (#7). See “Park Jack Assembly” on 
page 14. Check jack angle. If jack is not vertical, 
proceed with step 4 below.

4.

Remove 1/2" hex nut (#3), lock washer (#5) and 
carriage bolt (#2).

5.

Loosen 1" hex nut (#4). Do not remove.

6.

Rotate jack mount (#1) to align park jack (#7) as near 
vertical as possible.

7.

Replace 1/2"-13 x 1 1/2" GR5 carriage bolt (#2) and 
secure with lock washer (#5) and hex nut (#3). 
Tighten hex nut to the correct torque.

8.

Tighten 1" hex nut (#4) to 645 ft-lbs.

9.

If moving cutter, skip to step 10. If unhooking cutter, 
see “Unhook Rotary Cutter” on page 25 for detailed 
instructions. 

10. If cutter is to be moved, remove park jack (#7) from 

hitch frame and attach it to the weight box storage 
base. 

37576

NOTE:  If cutter is not hitched securely to a tractor, 
support blocks should be placed under the front 
skid shoes to support cutter while aligning the park 
jack vertically.

NOTE:  Refer to decal (#6) and instructions below 
for jack alignment and torque values.

These adjustments should be made with your cutter 
hooked to the tractor operating the unit or to a tractor 
having the same drawbar height.

Refer to Figure 2-2 & Figure 2-3 on page 27:
1.

Attach cutter to tractor and park on level ground.

2.

Raise wing up and lock into position with transport 
lock to keep wings from falling. 

3.

Using hydraulic lift, adjust center deck height so that 
the front skids (#5) are 2 to 3 inches above ground.

4.

Shut tractor down properly before dismounting. Refer 
to “Tractor Shutdown Procedure” on page 14.

5.

On both sides of the center deck are continuous 
hinges (#1). Measure distance from bottom of hinges 
to ground at the front and back. They should be equal 
distance off the ground at the back and 1" closer to 
the ground at the front than they are at the back. 

If continuous hinges are too high at the front:
a. Loosen jam nuts (#3) several turns. 

b. Unscrew adjusting nuts (#5) an equal amount to 

lower front of cutter until both hinges are inclined 
from front to back by 1" with the front being closer 
to the ground than the back.

If continuous hinges are too low at the front:
a. Loosen jam nuts (#3). 

b. Tighten adjusting nuts (#5) an equal amount to 

raise front of cutter until both hinges are inclined 
from front to back by 1" with the front being closer 
to the ground than the back.

6.

Be sure left and right leveling rods (#2) have equal 
amounts of tension and then re-tighten jam nuts (#3) 
against lock washers (#4) and adjusting nuts (#5).

NOTE:  Loosening adjusting nuts (#5) will lengthen 
leveling rods (#2) and lower front of cutter. 
Tightening adjusting nuts (#5) will shorten leveling 
rods (#2) and raise front of cutter.