Land Pride RCB6610 Manuale Utente

29

Section 3: Operating Instructions

11/11/12

RCB6610 & RCBM6610 Series 2 S/N 944730+ Rotary Cutters 330-584M

Table of Contents

!

DANGER

Do not raise wing up past 45 degrees with PTO engaged and
drivelines rotating. Objects can be thrown by rotating blades.
Always keep people away from a cutter that is operating.

!

DANGER

Do not operate cutter with a bent or broken driveline. Such a
driveline can break apart while rotating at high speeds
causing serious injury or death. Always remove Rotary Cutter
from service until damaged driveline is repaired or replaced.

!

DANGER

Keep others away from the cutter while it is operating. Rotary
Cutters have the ability to discharge objects at high speeds
causing serious injury or death. The use of front & rear safety
guards is strongly recommended and should always be used
when cutting along highways and in areas where bystanders
are present. Stop blade rotation if bystanders are nearby.

!

DANGER

Do not operate cutter without wing and weight box attached
to the center deck. Removing the wing or weight box will
expose blades and increase risk of cutter overturning.
Exposed blades can result in serious injury and/or death.

!

DANGER

Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.

!

DANGER

Never place hands or feet under the deck or attempt to make
adjustments to the cutter with PTO engaged. Cutter blades
rotating at high speeds cannot be seen and are located close
to the deck housing. Body extremities can be cut off instantly.

!

DANGER

Do not operate on or travel across steep inclines where a
tractor or cutter could roll-over resulting in serious injury or
death. Consult your tractor’s manual for acceptable inclines
the tractor is capable of traveling across.

!

DANGER

Clear area to be cut of debris and other unforeseen removable
objects before cutting. Mark any potential hazards that cannot
be removed such as tree stumps, posts, large rocks, holes, and
drop-offs with a visible flag.

Section 3: Operating Instructions

Startup Checklist

Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Rotary Cutter. Therefore, it is
absolutely essential that no one operates the cutter
without first having read, fully understood, and become
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:

•

Important Safety Information, pages 1 to 10

•

Section 1: Assembly & Set-up, page 12

•

Section 2: Adjustments, page 26

•

Section 3: Operating Instructions, page 29

•

Section 4: Options & Accessories, page 36

•

Section 5: Maintenance & Lubrication, page 40

Also make sure the operator has completed the
Operating Checklist below before using the cutter.

Safety Information

!

DANGER

Operate only tractors equipped with Roll-Over Protective
Structure (ROPS) and seat belt. Fasten seat belt snugly and
securely to help protect operator from being thrown, crushed,
or severely injured in a rollover or from falling off the tractor
and being ran over by the tractor and/or cutter.

!

DANGER

Never allow riders including children on the tractor or cutter.
They can fall and be ran over, become entangled in rotating
components, and/or pinched by moving components causing
serious injury or death.

!

DANGER

Always disconnect main driveline from tractor PTO before
servicing underside of cutter. PTO can be engaged if tractor is
started causing cutter damage, bodily injury or death.

Operating Checklist

✔

Check

Page

Make sure all guards and shields are in place and in
good working condition.
Refer to “Important Safety Information”.

Follow hook-up & driveline installation instructions.
Refer to “Section 1: Assembly & Set-up”.

Make all required adjustments.
Refer to “Section 2: Adjustments”.

Preform all required maintenance.
Refer to “Section 5: Maintenance & Lubrication”.

Lubricate cutter and driveline as needed.
Refer to “Lubrication Points”.

Lubricate all gearboxes and replace oil plugs
properly. Refer to Gearbox Lubrication.

Check cutter initially and periodically for loose bolts
and pins. Refer to “Torque Values Chart”.

Page 62