Land Pride rcfm3696 Manuale Utente

Section 5: Maintenance & Lubrication

12/15/15

RCF3696, RCFM3696, RCF3610, & RCFM3610 Rotary Cutters 326-600M

Section 5: Maintenance & Lubrication

Maintenance

Proper servicing and adjustments are key to the long life
of any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.

Check all bolts and pins after using the cutter for several
hours and on a regular basis thereafter to ensure they are
tight and secured. Replace worn, damaged or illegible
safety labels by obtaining new labels from your Land
Pride dealer.

DANGER

Perform maintenance only on a cutter that is not running.
Disengage PTO, place tractor in park or set park brake, shut
tractor engine off, remove switch key, and wait for blades to
come to a complete stop before dismounting tractor to perform
maintenance.

WARNING

Frequently check all hardware to make certain it is tight and
not broken or missing. Such hardware can cause the cutter to
not perform properly and may lead to breakage that can cause
bodily injury or death.

WARNING

Replace worn, damaged, or missing parts only with genuine
Land Pride parts. Replacing parts with other brands can
cause the equipment to not perform properly and may lead to
breakage that can cause bodily injury or death.

CAUTION

Do not alter Land Pride equipment or replace parts with other
brands. Doing so can cause equipment to perform improperly
and may lead to breakage that can cause bodily injury.
Replace parts only with genuine Land Pride parts.

CAUTION

Buildup of debris around moving parts and gearboxes is a fire
hazard. Keep rotating parts and gearboxes free from debris to
avoid serious injury and property damage.

CAUTION

Improper oil level can cause bearing failure and be a fire
hazard. Maintain proper gearbox oil level to avoid serious
injury and property damage.

Tractor Maintenance

One of the most important things you can do to prevent
hydraulic system problems is ensure that your tractor's
reservoir remains free of dirt and contamination.

Use a clean cloth to wipe hose ends before attaching
them to your tractor. Replace your tractor’s hydraulic filter
element at the prescribed intervals. These simple

maintenances will go a long way to prevent occurrence of
control valve and hydraulic cylinder problems.

Cutter Blade Maintenance

DANGER

Always disconnect driveline from tractor PTO shaft before
servicing underside of cutter. If tractor is started with PTO
engaged, the cutter can cause bodily injury or death.

DANGER

Always secure cutter deck in the up position with solid
supports before servicing underside of cutter. Never work
under equipment supported by hydraulics. Hydraulics can
drop equipment if controls are actuated or if hydraulic lines
burst. Either situation can drop the cutter instantly even when
power to the hydraulics is shut off.

WARNING

Keep blade bolt access hole covered at all times except when
servicing cutter blades. Make sure driveline is disconnected
from the tractor before servicing cutter blades.

WARNING

Do not operate cutter with blades that are out-of-balance,
bent, excessively worn, excessively nicked, or with blade bolts
that are excessively worn. Such blades can break loose from
the cutter at high speeds causing serious injury or death.

WARNING

Do not attempt to straighten a bent blade or weld on a blade.
Do not attempt to modify a blade such as hard surfacing, heat
treating, cold treating, or by any other method. Always
replace blades with a new Land Pride blade to assure safety.

Always inspect cutting blades before each use. Make
certain they are properly installed and are in good working
condition. Replace any blade that is damaged, worn, bent,
or excessively nicked. Small nicks can be ground out when
sharpening. Remove cutting blades and sharpen or
replace as follows:

Place tractor gear selector in park and/or set brakes,
shut engine off and remove ignition key.

Disconnect main driveline from tractor PTO and
secure cutter deck in the up position with solid
supports before servicing underside of cutter.

IMPORTANT: Replace cutting blades in pairs with
genuine Land Pride blades only. Replacing single
blades can result in an out-of-balance condition that
will contribute to premature bearing wear/breakage
and/or structural cracks in gearbox and/or deck.