Land Pride AR2596 Manuale Utente

12/09/15

3.

Attach SMV bracket (#3) to back bar of lift frame (#1) 
with 1/2"-13 x 2" x 3" GR5 U-bolt (#13) and hex flange 
lock nuts (#6). Torque nuts tight.

4.

Apply teflon tape to the 3/8" threads of straight 
adapter (#15) and screw adapter into the cylinder 
port located closest to the rod end of hydraulic 
cylinder (#14). Tighten adapter.

5.

Apply teflon tape to the 3/8" threads of elbow 
fitting (#16) and screw elbow into the cylinder port 
located closest to the base end of hydraulic cylinder 
(#14). Tighten elbow oriented as shown.

6.

Attach 3/8" x 201" long hydraulic hoses (#17) to 
adapter fitting (#15). 

7.

Attach 3/8" x 217" long hydraulic hoses 
(#18) to elbow fitting (#16). 

Refer to Figure 2-4 on page 11:
8.

Attach 3/4" adapters (#23) to hose ends and tighten.

9.

Attach quick disconnect couplings (#24) to the 
adapters tighten.

Refer to Figure 2-3 on page 11:
10. Orient hoses so that they are on the right side of the 

cylinder (#14). Attach base end of hydraulic cylinder 
to the Aerator frame with cylinder pin (#2). 

11. Attach rod end of hydraulic cylinder (#14) to the lift 

frame with cylinder pin (#2) & flat washer (#8). 

12. Insert 3/16" x 1 3/4" cotter pins (#9) into cylinder 

pins (#2). Bend one or both legs to secure them in 
place.

Refer to Figure 2-4:
13. Insert hydraulic hoses (#17 & #18) into the open end 

of the tongue located at the back of the main frame. 
Push both hoses together through the tongue and 
out the front (#22) as shown in Figure 2-4. 

14. Pivot lift frame up and down to find the maximum 

distance between hydraulic cylinder and opening 
end of tongue. Pull hydraulic hoses (#17 & #18) out of 
end (#22) until most of the slack in the hoses have 
been removed. 

15. Run hydraulic hoses through hose loop (#21).

16. Pivot lift frame fully up and down to make sure the 

hydraulic hoses are not hanging up.

Refer to Figure 2-3 on page 11:
17. Attach transport bar (#4) to the left side of the lift 

frame and secure in place with hairpin cotters (#10).

30066

Refer to Figure 2-2 on page 10:
Always use heavy duty tie-downs, straps, and corner 
protector pads (strap & pads supplied by customer) to 
secure Land Pride concrete blocks from bouncing on the 
platform while traveling over rough terrain and on a road 
that may have bumps and ruts. Corner protector 
pads (#5) are available through Land Pride’s Parts 
Department. Order 2 each of Part No. 816-646C.

1.

Attach strap to handle “A” on the left side.

2.

Thread strap through corner protector pad (#5) on 
the left side, lifting rods “B”, corner protector pad (#5) 
on the right side and to handle “C”. Tighten strap to 
secure blocks in place. 

1.

Orient lift frame (#1) as shown and pin to Aerator 
frame with 1" x 6" hitch pins (#11). Secure hitch pin 
with hairpin cotters (#12).

2.

Attach SMV sign (#19) to SMV bracket (#3) with 
1/4"-20 x 5/8" round head screws (#5) and hex flange 
top lock nuts (#7). Tighten nuts.

NOTE:  Weights can bounce out if bump is severe.

30065

NOTE:  Drag Harrow Carrier and Drag Harrow are 
sold separately.

IMPORTANT: Make sure the Aerator is properly 
supported so that it won’t flip over backwards during 
installation of the lift frame. One method would be to 
hitch the tongue to a tractor.