Poulan 96042004201 Manuale Utente
7
ASSEMBLY
FIG. 4
CHECK BATTERY (See Fig. 4)
•
Lift seat pan to raised position.
•
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions).
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions).
SEAT PAN
LABEL
TERMINAL
TERMINAL
•
Push down on seat to engage pads in slots and pull
seat towards rear of tractor.
seat towards rear of tractor.
•
Raise seat and tighten bolt securely.
•
Remove tape and discard.
•
Lower seat into operating position and sit on seat.
Press clutch/brake pedal all the way down. If operating
position is not comfortable, adjust seat.
Press clutch/brake pedal all the way down. If operating
position is not comfortable, adjust seat.
To adjust seat: Grasp adjustment handle and pull up, slide
seat to desired po si tion and release adjustment handle.
seat to desired po si tion and release adjustment handle.
Fig. 3
BOLT
FLAT
WASHER
WASHER
SEAT PAN
PAD
TAPE
SLOT
TAB
ADJUSTMENT
HANDLE
NOTE: You may now roll or drive your tractor off the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid.
WARNING: Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
er a tion section for location and function of
con trols)
•
Press lift lever plunger and raise attachment lift lever
to its highest po si tion.
to its highest po si tion.
•
Release parking brake by de
press ing clutch/brake
ped al.
•
Place freewheel control in "trans mis sion dis en gaged
position" (See “TO TRANS PORT” in the Op er a tion
section of this manual).
position" (See “TO TRANS PORT” in the Op er a tion
section of this manual).
•
Roll tractor forward off skid.
•
Remove banding holding the deflector shield up against
tractor.
tractor.
TO DRIVE TRAC
TOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
con trols)
•
Be sure all the above assembly steps have been com-
pleted.
pleted.
•
Check engine oil level and fill fuel tank with gasoline.
•
Place freewheel control in "trans
mis sion en
gaged"
po si tion (see "TO TRANSPORT" in Op er a tion section
of this manual).
of this manual).
•
Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
pedal and set the parking brake.
•
Place motion control lever in neutral (N) position.
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
to its highest position.
•
Remove key from bag and start the engine (see "TO
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
•
Release parking brake.
•
Slowly move the mo tion control lever for ward and slowly
drive tractor off skid.
drive tractor off skid.
•
Apply brake to stop trac tor, set park ing brake and place
motion con trol lever in neutral po si tion.
motion con trol lever in neutral po si tion.
•
Turn ignition key to "STOP" position.
Continue with the in struc tions that follow.