Poulan AG17542STB Manuale Utente
25
TO START ENGINE WITH A WEAK
BAT TERY
BAT TERY
WARNING: Lead-acid batteries gen-
er ate ex plo sive gases. Keep sparks, fl ame
and smoking ma te ri als away from bat-
ter ies. Always wear eye pro tec tion when
around batteries.
If your battery is too weak to start the
engine, it should be recharged. (See "BAT-
TERY" in the MAINTENANCE section of
this man u al).
If “jumper ca bles” are used for emer gen cy
starting, follow this pro ce dure:
IMPORTANT: Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.
and smoking ma te ri als away from bat-
ter ies. Always wear eye pro tec tion when
around batteries.
If your battery is too weak to start the
engine, it should be recharged. (See "BAT-
TERY" in the MAINTENANCE section of
this man u al).
If “jumper ca bles” are used for emer gen cy
starting, follow this pro ce dure:
IMPORTANT: Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.
TO ATTACH JUMPER CABLES -
1. Connect one end of the RED cable
1. Connect one end of the RED cable
to the POSITIVE (+) terminal of each
battery(A-B), taking care not to short
against tractor chassis.
battery(A-B), taking care not to short
against tractor chassis.
2. Connect one end of the BLACK ca ble
to the NEGA TIVE (-) terminal (C) of
fully charged battery.
fully charged battery.
3. Connect the other end of the BLACK
cable (D) to good chassis ground,
away from fuel tank and bat tery.
away from fuel tank and bat tery.
TO REMOVE CABLES, REVERSE
ORDER -
1. BLACK cable fi rst from chassis and
ORDER -
1. BLACK cable fi rst from chassis and
then from the fully charged battery.
2. RED cable last from both batteries.
02614
Weak or Dead
Battery
Battery
Fully Charged
Battery
Battery
REPLACING BATTERY
WARNING: Do not short bat tery
ter mi nals by al low ing a wrench or any
other object to contact both terminals at
the same time. Before con nect ing battery,
remove metal bracelets, wrist watch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent spark ing from ac ci den tal
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable fi rst
other object to contact both terminals at
the same time. Before con nect ing battery,
remove metal bracelets, wrist watch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent spark ing from ac ci den tal
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable fi rst
then RED battery cable and carefully
remove battery from trac tor.
remove battery from trac tor.
3. Install new battery with terminals in
same position as old battery.
4. First connect RED battery cable to
positive (+) terminal with hex bolt and
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
5. Connect BLACK grounding cable to
negative (-) ter mi nal with remaining
hex bolt and keps nut. Tighten se cure ly.
hex bolt and keps nut. Tighten se cure ly.
02602
02603
Seat Pan
Keps Nut
Positive
(Red)
Cable
(Red)
Cable
Hex
Bolt
Bolt
Terminal Cover
Negative
(Black) Cable
(Black) Cable
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Pull bulb holder out of the hole in the
1. Raise hood.
2. Pull bulb holder out of the hole in the
backside of the grill.
3. Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
the backside of the grill.
4. Close hood.