Hayter Mowers RZT420H Manuale Utente
Without the grass deflector, discharge cover,
or complete grass catcher assembly mounted
in place, you and others are exposed to blade
contact and thrown debris. Contact with
rotating cutter deck blade(s) and thrown debris
will cause injury or death.
or complete grass catcher assembly mounted
in place, you and others are exposed to blade
contact and thrown debris. Contact with
rotating cutter deck blade(s) and thrown debris
will cause injury or death.
•
Never remove the grass deflector from the
cutter deck because the grass deflector
routes material down toward the turf. If the
grass deflector is ever damaged, replace it
immediately.
cutter deck because the grass deflector
routes material down toward the turf. If the
grass deflector is ever damaged, replace it
immediately.
•
Never put your hands or feet under the
cutter deck.
cutter deck.
•
Never try to clear discharge area or cutter
deck blades unless you move the blade
control switch to Off and rotate the ignition
key to Off. Also remove the key and pull the
wire off the spark plug(s).
deck blades unless you move the blade
control switch to Off and rotate the ignition
key to Off. Also remove the key and pull the
wire off the spark plug(s).
Removing and Installing the
Discharge Cover
Discharge Cover
The cutter deck and mower blades shipped with
this machine were designed for optimum mulching
performance. Side discharge performance can be
improved by replacing the mulching blades with
standard cutting blades obtained from your local
authorized Hayter dealer. To maintain optimum
mulching performance, always install the mulching
blades that are shipped with this unit when changing
back to mulching operation.
this machine were designed for optimum mulching
performance. Side discharge performance can be
improved by replacing the mulching blades with
standard cutting blades obtained from your local
authorized Hayter dealer. To maintain optimum
mulching performance, always install the mulching
blades that are shipped with this unit when changing
back to mulching operation.
Removing the Discharge Cover for
Side Discharge
Side Discharge
Note: If the bagger attachment is added the machine,
standard blades must be installed for proper bagging
function.
standard blades must be installed for proper bagging
function.
1. Park the machine on a level surface and disengage
the blade control switch.
2. Move the motion control levers outward to park
position, stop the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.
for all moving parts to stop before leaving the
operating position.
3. Remove the two bolts (1/4 x 2-1/2 inches) and two
cap nuts (1/4 inch) that secure the discharge cover
to the cutter deck (Figure 25).
to the cutter deck (Figure 25).
Figure 25
1.
Bolt (1/4 x 2-1/2 inches)
3.
Discharge cover
2.
Cap nut (1/4 inch)
4. Remove the discharge cover and lower the grass
deflector over the discharge opening as shown in
Figure 25.
Figure 25.
Important: Ensure the cutter deck has a
hinged grass deflector that disperses clippings
to the side and down toward the turf, while in
side discharge mode.
hinged grass deflector that disperses clippings
to the side and down toward the turf, while in
side discharge mode.
Installing the Discharge Cover for
Mulching
Mulching
1. Park the machine on a level surface and disengage
the blade control switch.
2. Move the motion control levers outward to park
position, stop the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.
for all moving parts to stop before leaving the
operating position.
3. Lift the grass deflector and slide the tabs on top
of the discharge cover under the grass deflector
retaining rod. Rotate the discharge cover down over
the opening, and onto the lower lip of the cutter
deck (Figure 25).
retaining rod. Rotate the discharge cover down over
the opening, and onto the lower lip of the cutter
deck (Figure 25).
4. Secure the discharge cover to the lower lip of the
cutter deck with two bolts (1/4 x 2-1/2 inches) and
two cap nuts (1/4 inch) as shown in Figure 25.
two cap nuts (1/4 inch) as shown in Figure 25.
Note: Do not overtighten the nuts; this could
distort the cover and cause blade contact.
distort the cover and cause blade contact.
23