Azden 310LT Manuale Utente
3
Operating the System
WARNING
WARNING
・Do not use other batteries than the ones specified in this manual. Do not mix a fresh
battery with a used battery.
・When installing batteries, make sure battery polarity is correct as marked inside the
battery compartment.
・Remove the batteries if the products are not used for a long period of time.
・Do not submerge the products.
・Do not submerge the products.
Because this is a frequency agile system, the receiver and transmitter must be on the same
channel number. To change the channel selection, use a small , sharp object such as the tip of
a pen, and press the “UP” or “DOWN” button to the desired channel. Make sure both the re-
ceiver and transmitter are on the same channel.
310UDR Diversity Receiver
channel number. To change the channel selection, use a small , sharp object such as the tip of
a pen, and press the “UP” or “DOWN” button to the desired channel. Make sure both the re-
ceiver and transmitter are on the same channel.
310UDR Diversity Receiver
After installing new batteries, mount the receiver to your video camera with supplied
shoe mount or hook & loop fastener. Select one of the supplied cables and connect the
output on the receiver and input on the video camera. Turn the power switch to “ON”
and the battery level indicator on the LCD display should come on. If not, check the
batteries. When the 310UDR receives a signal from the transmitter, the reception level
indicator will come on. If it does not, make sure both the receiver and the transmitter
are on matching channels.
shoe mount or hook & loop fastener. Select one of the supplied cables and connect the
output on the receiver and input on the video camera. Turn the power switch to “ON”
and the battery level indicator on the LCD display should come on. If not, check the
batteries. When the 310UDR receives a signal from the transmitter, the reception level
indicator will come on. If it does not, make sure both the receiver and the transmitter
are on matching channels.
35BT Body-Pack Transmitter
Plug in the supplied EX-503L Lavalier Microphone and clip it to your subject. The micro-
phones should be placed 4”-12” from the subject’s mouth. Clip the transmitter to a
belt by using the supplied belt clip or place it in a pocket. Turn the power switch to
“ON” and the battery level indicator on the LCD display should come on. If not, check
the battery. Have someone speak into the microphone as you monitor the sound
through the 310UDR Receiver’s phone output. If the sound is distorted, lower the MIC
input level on the 35BT Transmitter. If there is not enough volume, raise the MIC input
level on the Transmitter.
phones should be placed 4”-12” from the subject’s mouth. Clip the transmitter to a
belt by using the supplied belt clip or place it in a pocket. Turn the power switch to
“ON” and the battery level indicator on the LCD display should come on. If not, check
the battery. Have someone speak into the microphone as you monitor the sound
through the 310UDR Receiver’s phone output. If the sound is distorted, lower the MIC
input level on the 35BT Transmitter. If there is not enough volume, raise the MIC input
level on the Transmitter.
35XT Plug-in Transmitter
Attach the 35XT Transmitter to any low impedance microphone with a corresponding 3-
pin XLR connector. Turn the power switch on the 35XT Transmitter to “ON” position
and the battery level indicator on the LCD display should come on. Have someone
speak into the microphone as you monitor the sound through the camera’s monitor
output. If the sound is distorted, lower the MIC input level control on the 35XT Trans-
mitter. If there is not enough volume, raise the level control on the Transmitter.
pin XLR connector. Turn the power switch on the 35XT Transmitter to “ON” position
and the battery level indicator on the LCD display should come on. Have someone
speak into the microphone as you monitor the sound through the camera’s monitor
output. If the sound is distorted, lower the MIC input level control on the 35XT Trans-
mitter. If there is not enough volume, raise the level control on the Transmitter.