Roland V-Synth Manuale Utente
74
Settings Common to All Modes (System Mode)
Functions of System
Parameters
This section explains what the different System parameters do, and
also how these parameters are organized.
also how these parameters are organized.
Settings Common to the Entire
System (Common)
Master
fig.05-01_50
Master Tune
Adjusts the overall tuning of the V-Synth. The display shows the
frequency of the A4 note (center A).
frequency of the A4 note (center A).
Value:
415.3–466.2 Hz
Master Key Shift
Shifts the overall pitch of the V-Synth in semitone steps.
Value:
-24– +24
Master Level
Adjusts the volume of the entire V-Synth.
Value:
0–127
Patch Remain (Patch Remain Switch)
Specifies whether currently sounding notes will continue sounding
when another patch is selected (ON), or not (OFF).
when another patch is selected (ON), or not (OFF).
Also, when this is “ON,” changes produced by incoming MIDI
messages such as Volume (CC 7) or Pan (CC 10), as well as tonal
quality and volume changes produced by the various controllers will
be inherited.
messages such as Volume (CC 7) or Pan (CC 10), as well as tonal
quality and volume changes produced by the various controllers will
be inherited.
Value:
OFF, ON
Effects settings change as soon as you switch to a new patch,
without being influenced by the Patch Remain setting. Because
of this, certain effects settings can cause notes that were until
then sounding to no longer be heard, even though Patch Remain
has been set to on.
without being influenced by the Patch Remain setting. Because
of this, certain effects settings can cause notes that were until
then sounding to no longer be heard, even though Patch Remain
has been set to on.
Powerup Mode
Specifies the condition that the V-Synth will be in when the power is
turned on.
turned on.
Value
LAST SET:
Reinstates the patch selected at the time the V-Synth was
last turned off.
DEFAULT:
The V-Synth will be ready to play Patch “001.”
IO
fig.05-01a_50
External Input Type
Value
STEREO L R:
Input in stereo.
MONORAL MIX:
Mix the L and R input signals and input in
monaural.
MONORAL L:
Input the L signal in monaural.
MONORAL R:
Input the R signal in monaural.
Mix/Parallel
Specifies how the sound of the entire V-Synth will be output.
Value
MIX:
Set this to have the collective output of all sounds output from
the OUTPUT A (MIX) jacks. When you want to check the final
overall sound being output, set to MIX.
overall sound being output, set to MIX.
Sounds output from the PHONES jack are the same as those
output from the MIX OUT jacks. Therefore, any sounds set with
Output Assign to be output from the DIRECT OUT jacks is not
output from the PHONES jack. Be sure to have any sound you
want to hear through the headphones set to “MIX.”
output from the MIX OUT jacks. Therefore, any sounds set with
Output Assign to be output from the DIRECT OUT jacks is not
output from the PHONES jack. Be sure to have any sound you
want to hear through the headphones set to “MIX.”
PARALLEL:
Output according to each Output Assign settings.
Output Gain
This adjusts the output gain from the V-Synth’s Analog Out and
Digital Out. When, for example, there are relatively few voices being
sounded, boosting the output gain can let you attain the most
suitable output level for recording and other purposes.
Digital Out. When, for example, there are relatively few voices being
sounded, boosting the output gain can let you attain the most
suitable output level for recording and other purposes.
Value:
-12–+12 dB
Digital Output Freq (Digital Output Frequency)
Sets the sampling frequency of the digital output.
Value:
44.1, 48, 96 KHz