Roland XV-88 Manuale Utente
60
Chapter 4. Zone Settings
You can also set the transmit switch settings on the
PERFORM PLAY page. When the [EDIT] indicator is
extinguished and the [LOCAL/TX] indicator is lit, press
ZONE/PART SELECT [1/9]–[8/16] to make settings. A
Layer Performance is on when the indicator is lit, and off
when the indicator is extinguished. When the [1-8/9-16]
indicator is extinguished, Zones 1–8 are switched on and
off, and when the [1-8/9-16] indicator is lit, Zones 9–16
are switched on and off.
PERFORM PLAY page. When the [EDIT] indicator is
extinguished and the [LOCAL/TX] indicator is lit, press
ZONE/PART SELECT [1/9]–[8/16] to make settings. A
Layer Performance is on when the indicator is lit, and off
when the indicator is extinguished. When the [1-8/9-16]
indicator is extinguished, Zones 1–8 are switched on and
off, and when the [1-8/9-16] indicator is lit, Zones 9–16
are switched on and off.
Local (Local Switch)
Specifies, for each Zone, whether or not the keyboard
controller section will be connected to the internal sound
generator.
controller section will be connected to the internal sound
generator.
Normally you will leave this ON, but you can turn it OFF
when you want to use the XV-88 only to control an external
sound generator.
when you want to use the XV-88 only to control an external
sound generator.
You can also set the Local switch setting on the
PERFORM PLAY page. When the [EDIT] indicator and
the [LOCAL/TX] indicator is extinguished, press
ZONE/PART SELECT [1/9]–[8/16] to make settings. A
Layer Performance is on when the indicator is lit, and off
when the indicator is extinguished. When the [1-8/9-16]
indicator is extinguished, Zones 1–8 are switched on and
off, and when the [1-8/9-16] indicator is lit, Zones 9–16
are switched on and off.
PERFORM PLAY page. When the [EDIT] indicator and
the [LOCAL/TX] indicator is extinguished, press
ZONE/PART SELECT [1/9]–[8/16] to make settings. A
Layer Performance is on when the indicator is lit, and off
when the indicator is extinguished. When the [1-8/9-16]
indicator is extinguished, Zones 1–8 are switched on and
off, and when the [1-8/9-16] indicator is lit, Zones 9–16
are switched on and off.
Controlling External Sound
Module (EXT CONTROL)
Module (EXT CONTROL)
When a Single Performance is selected, this setting is
disabled.
disabled.
EXT P.C (External Program Change)
fig.04-09
When switching Performances, send MIDI messages
(Program Change/Bank Select) to each Zone to switch the
Tones corresponding to the external sound module.
(Program Change/Bank Select) to each Zone to switch the
Tones corresponding to the external sound module.
After setting each value, you can transmit it by pressing
[ENTER].
[ENTER].
The data of the Zone for which the Transmit switch is
turned off will not be transmitted.
turned off will not be transmitted.
P.C# (External Program Change Number)
Selects the Program Change number you wish to transmit. If
you do not want this message to be transmitted, set this to
NO-SEND.
you do not want this message to be transmitted, set this to
NO-SEND.
Bank Select MSB/LSB
(External Bank Select MSB/LSB)
(External Bank Select MSB/LSB)
Selects the Bank Select number MSB (Controller number 0)
and LSB (Controller number 32) you want to transmit.
and LSB (Controller number 32) you want to transmit.
Information on the XV-88 Tone Group/Bank
corresponding to the Bank Select message sent is
displayed in parentheses.
corresponding to the Bank Select message sent is
displayed in parentheses.
EXT CTRL (External Control)
fig.04-10
Volume (External Volume)
If you want Volume messages to also be transmitted when
you select a Performance, specify the desired value (0–127)
for the Zone. Turn this parameter NO-SEND if you do not
want this data to be transmitted.
you select a Performance, specify the desired value (0–127)
for the Zone. Turn this parameter NO-SEND if you do not
want this data to be transmitted.
The data of the Zone for which the Transmit switch is
turned off will not be transmitted.
turned off will not be transmitted.
Pan (External Pan)
If you want Pan messages to also be transmitted when you
select a Performance, specify the desired value (0–127) for the
Zone. Turn this parameter NO-SEND if you do not want this
data to be transmitted.
select a Performance, specify the desired value (0–127) for the
Zone. Turn this parameter NO-SEND if you do not want this
data to be transmitted.
The data of the Zone for which the Transmit switch is
turned off will not be transmitted.
turned off will not be transmitted.