Roland C-200 Manuale Utente

 

 

• Do not connect this unit to same electrical outlet that is being 

used by an electrical appliance that is controlled by an 
inverter (such as a refrigerator, washing machine, microwave 
oven, or air conditioner), or that contains a motor. Depending 
on the way in which the electrical appliance is used, power 
supply noise may cause this unit to malfunction or may 
produce audible noise. If it is not practical to use a separate 
electrical outlet, connect a power supply noise filter between 
this unit and the electrical outlet.

• The AC adaptor will begin to generate heat after long hours 

of consecutive use. This is normal, and is not a cause for 
concern.

• Before connecting this unit to other devices, turn off the 

power to all units. This will help prevent malfunctions and/
or damage to speakers or other devices.

 

• Using the unit near power amplifiers (or other equipment 

containing large power transformers) may induce hum. To 
alleviate the problem, change the orientation of this unit; or 
move it farther away from the source of interference.

• This device may interfere with radio and television reception. 

Do not use this device in the vicinity of such receivers.

• Noise may be produced if wireless communications devices, 

such as cell phones, are operated in the vicinity of this unit. 
Such noise could occur when receiving or initiating a call, or 
while conversing. Should you experience such problems, you 
should relocate such wireless devices so they are at a greater 
distance from this unit, or switch them off.

• Do not expose the unit to direct sunlight, place it near devices 

that radiate heat, leave it inside an enclosed vehicle, or 
otherwise subject it to temperature extremes. Also, do not 
allow lighting devices that normally are used while their light 
source is very close to the unit (such as a piano light), or 
powerful spotlights to shine upon the same area of the unit 
for extended periods of time. Excessive heat can deform or 
discolor the unit.

• When moved from one location to another where the temper-

ature and/or humidity is very different, water droplets 
(condensation) may form inside the unit. Damage or 
malfunction may result if you attempt to use the unit in this 
condition. Therefore, before using the unit, you must allow it 
to stand for several hours, until the condensation has 
completely evaporated.

• Do not allow rubber, vinyl, or similar materials to remain on 

the unit for long periods of time. Such objects can discolor or 
otherwise harmfully affect the finish.

• Do not allow objects to remain on top of the keyboard. This 

can be the cause of malfunction, such as keys ceasing to 
produce sound.

• Do not paste stickers, decals, or the like to this instrument. 

Peeling such matter off the instrument may damage the 
exterior finish.

• Depending on the material and temperature of the surface on 

which you place the unit, its rubber feet may discolor or mar 
the surface. You can place a piece of felt or cloth under the 
rubber feet to prevent this from happening. If you do so, 
please make sure that the unit will not slip or move acciden-
tally.

• Do not put anything that contains water (e.g., flower vases) 

on this unit. Also, avoid the use of insecticides, perfumes, 
alcohol, nail polish, spray cans, etc., near the unit. Swiftly 
wipe away any liquid that spills on the unit using a dry, soft 
cloth.

 

• To clean the unit, use a dry, soft cloth; or one that is slightly 

dampened. Try to wipe the entire surface using an equal 
amount of strength, moving the cloth along with the grain of 
the wood. Rubbing too hard in the same area can damage the 
finish.

• Never use benzine, thinners, alcohol or solvents of any kind, 

to avoid the possibility of discoloration and/or deformation.

 

• Unfortunately, it may be impossible to restore the contents of 

data that was stored on a USB storage device once it has been 
lost. Roland Europe assumes no liability concerning such loss 
of data.

• Use a reasonable amount of care when using the unit’s 

buttons, sliders, or other controls; and when using its jacks 
and connectors. Rough handling can lead to malfunctions.

• When connecting / disconnecting all cables, grasp the 

connector itself—never pull on the cable. This way you will 
avoid causing shorts, or damage to the cable’s internal 
elements.

• To avoid disturbing your neighbors, try to keep the unit’s 

volume at reasonable levels. You may prefer to use 
headphones, so you do not need to be concerned about those 
around you (especially when it is late at night).

• When you need to transport the unit, package it in the box 

(including padding) that it came in, if possible. Otherwise, 
you will need to use equivalent packaging materials.

• Do not apply undue force to the music stand while it is in use.
• Use only the specified expression pedal (EV-7 or EV-5; sold 

separately). By connecting any other expression pedals, you 
risk causing malfunction and/or damage to the unit.

 

• When connecting USB memory, firmly insert it all the way 

into the USB memory port.

• Do not touch the pins of the USB memory port, or allow them 

to become dirty.

• USB memory is made using high-precision electronic compo-

nents, so please observe the following points when handling 
it.

• To prevent damage from static electrical charges, 

discharge any static electricity that might be present in 
your body before handling USB memory.

• Do not touch the terminals with your fingers or any metal 

object.

• Do not bend or drop USB memory, or subject it to strong 

impact.

• Do not leave USB memory in direct sunlight or in 

locations such as a closed-up automobile. (Storage 
temperature: 0~50°C)

• Do not allow USB memory to become wet.
• Do not disassemble or modify USB memory.

• When connecting USB memory, position it horizontally with 

the C-200’s USB Memory port and insert it without using 
excessive force. The USB memory connector may be damaged 
if you use excessive force when inserting USB memory.

 

C-200_e.book  Page 6  Monday, April 4, 2011  5:22 PM