Roland FC-200 Manuale Utente
43
MODE STATUS (Individual area)
Address(H) Size(H)
Data(H) Parameter
Description
——————————————————————————————
03 00
03 00
00 01
00-03
Mode Status *1 0: Program Mode
1: Control Mode
2: Note Mode
3: Exclusive Mode
2: Note Mode
3: Exclusive Mode
03 01
00 01
00-03
Mode Status *2 0: Program Mode
1: Control Mode
2: Note Mode
3: Exclusive Mode
2: Note Mode
3: Exclusive Mode
*1 Outputs on power-up or when Mode change is made.
Also outputs upon receiving Data Request RQ1.
Data Set DT1 is ignored.
Data Set DT1 is ignored.
*2 Outputs when Data Request RQ1 is received.
Mode is changed when Data Set DT1 is received.
BANK NUMBER (Individual area)
Address(H)
Size(H)
Data(H)
Parameter
Description
——————————————————————————————
04 00
04 00
00 01
00-63
Bank Number *1
0-99
Outputs when Data Request RQ1 is received.
Bank Number is changed when Data Set DT1 is received.
The value exceeding the Bank Limit automatically falls to the limit value.
Bank Number is changed when Data Set DT1 is received.
The value exceeding the Bank Limit automatically falls to the limit value.
*1 This is not a Bank Select Number.
EDIT PARAMETERS (Individual area)
Address(H) Size(H)
Data
Parameter
Description
——————————————————————————————
05 00
05 00
00 01
00000abcB Bank Status *1
05 01
00 01
00-63H
Bank Limit
0-99
05 02
00 01
rrH
Pedal 1 Assign Message *2
05 03
00 01
rrH
Pedal 2 Assign Message *2
:
:
:
:
05 0B
00 01
rrH
Pedal 10 Assign Message *2
05 0C
00 01
rrH
Pedal UP Assign Message *2
05 0D
00 01
rrH
Pedal DOWN Assign Message *2
05 0E
00 01
rrH
Pedal CTL Assign Message *2
05 0F
00 01
ccH
EXP Pedal Assign Message *3
05 10
00 01
rrH
Foot SW/EXP 1 Assign Message *2
:
:
:
:
05 15
00 01
rrH
Foot SW/EXP 6 Assign Message *2
05 16
00 01
00abcdefB Latch Status Upper *4
05 17
00 01
0ghijklmB Latch Status Lower *4
05 18
00 01
00-03H
Mode Jack Loop *5
05 19
00 01
00-08H
Note Range
C0-C8
05 1A
00 01
00-08H
Octave shift High
C0-C8
05 1B
00 01
00-08H
Octave shift Low
C0-C8
05 1C
00 01
01-7FH
Note On Velocity
1-127
05 1D
00 01
00/01H
Pedal CTL Latch Status *6 OFF/ON
Outputs when Data Request RQ1 is received.
Value of each edit parameter changes when Data Set DT1 is received.
Value of each edit parameter changes when Data Set DT1 is received.
*1 Each bit has the following meaning.
Each bit represents OFF when it is set at “0” and ON when set at “1”.
0000abcB
0000abcB
a: Number pedal is used to select Bank.
b: Outputs Program Change information upon Bank
b: Outputs Program Change information upon Bank
change.
c: Outputs Bank Select information.
*2 rr = 01-1F, 21-5F, 60-6B
*3 cc = 01-1F, 21-5F
rr and cc data represent output messages to be assigned to pedal.
01-1F, 21-5F:
Controller Number
(1-31, 33-95)
60, 61, 62:
Realtime Message
Start, Stop, Continue
63, 64, 65:
MMC(MIDI Machine Control) Command
Stop, Play, Deferred Play
66, 67, 68:
MMC Command
Fast Foward, Rewind,
Record Strobe
Record Strobe
69, 6A, 6B:
MMC Command
Record Exit, Record Pause,
Pause
Pause
* Only Controller Number can be assigned to each Expression pedal.
*4 Each bit reflects latch/momentary setting of each pedal:
0 = momentary; 1 = latch
Latch Status Upper
Latch Status Lower
00abcdefB
a: Pedal 6
0ghijklmB
g: Pedal 1
b: Pedal 7
h: Pedal 2
:
:
e: Pedal 10
k: Pedal 5
f: Pedal UP
l: Pedal DOWN
m: Pedal CTL
m: Pedal CTL
*5 Shows the modes selected by foot switch inserted into the MODE
socket.
Each data sets as shown below:
Each data sets as shown below:
0: PROGRAM Mode -> CONTROL Mode -> PROGRAM Mode -> ...
1: PROGRAM Mode -> CONTROL Mode -> NOTE Mode ->
PROGRAM Mode -> ...
2: PROGRAM Mode -> CONTROL Mode -> EXCLUSIVE Mode ->
PROGRAM Mode -> ...
3: PROGRAM Mode -> CONTROL Mode -> NOTE Mode ->
EXCLUSIVE Mode -> PROGRAM Mode -> ...
*6 Parameter which changes Pedal CTL Latch Status only. Latch Status
can also be changed by *4 Latch Status.
When both parameters are received, the status of the latter has
priority.
When both parameters are received, the status of the latter has
priority.
*7 When the massage assigned to the pedal contains information other
than
Controller Number, Latch cannot be turned on.
Controller Number, Latch cannot be turned on.
*8 When transmitting EDIT parameter messages in sequence, the interval
between messages must be 20 msec or longer.
FLIP-FLOP STATUS (Individual area)
Address(H)
Size(H)
Data(H)
Parameter
Description
——————————————————————————————
06 00
06 00
00 01
00/7F
Pedal 1 flip-flop
OFF/ON
06 01
00 01
00/7F
Pedal 2 flip-flop
OFF/ON
:
:
:
:
:
06 09
00 01
00/7F
Pedal 10 flip-flop
OFF/ON
06 0A
00 01
00/7F
Pedal UP flip-flop
OFF/ON
06 0B
00 01
00/7F
Pedal DOWN flip-flop OFF/ON
06 0C
00 01
00/7F
Pedal CTL flip-flop
OFF/ON
Outputs when Data Request RQ1 is received.
Flip-flop of each pedal changes when Data Set DT1 is received.
Indicator lights if pedal flip-flop is ON while in the CONTROL CHANGE
Mode.
*1 Ignored if the pedal is set at momentary.
Flip-flop of each pedal changes when Data Set DT1 is received.
Indicator lights if pedal flip-flop is ON while in the CONTROL CHANGE
Mode.
*1 Ignored if the pedal is set at momentary.
NOTE RANGE STATUS (Individual area)
Address(H)
Size(H)
Data(H)
Parameter
Description
——————————————————————————————
07 00
07 00
00 01
00-08
Current Note Range
C0-C8
Outputs when Data Request RQ1 is received.
Current note range is changed upon receiving Data Set DT1.
*1 This is not an Edit parameter.
Current note range is changed upon receiving Data Set DT1.
*1 This is not an Edit parameter.