Stanton SK FIVE Manuale Utente

TE C H N I C A L S P E C I FI C AT I O N S

Line inputs:

2 (RCA), 150 mV / 27K ohm

Phono inputs:

2 (RCA), 3 mV / 47K ohm

Master output:

1 (1/4” TRS Balanced/RCA unbalanced),
775 mV / 1K ohm

Record output:

1 (RCA), 245 mV / 10K ohm

Headphone output:

1 (1/4 inch), 32 - 200 ohms recommended

Frequency Response:

20 Hz - 20 kHz, +/- 2 dB

Gain Control:

0-20dB

S/N Ratio:

Less than 70dB

T.H.D:

less than 0.2%

Dimension(LxWxD):

9” x 9.75” x 3.5” ( 226 x 248 x 87 mm)

Weight:

7 lbs (3.2 Kg)

WA R R A N T Y

This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of twelve
(12) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:

• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles

Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.

FOR THE WA R R A N TY TO BE VA LID, PLEASE CO M PLE TE THE

O N LINE WA R R A N TY REGIST R ATION FORM FOUND AT

W W W. STA N TO N M AG N E TI CS . CO M

2821 Evans Street • Hollywood, FL 33020

FA D E R C LE A N I N G

The SK FIVE faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.

R E PL AC E M E N T PA RT S

To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.

ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES

Cleaning Instructions

1. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTEKT™
(see “

” inside) panel

and take the panel off the mixer.

2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the

cable coming from the mixer.

3. Spray a small amount of cleaner or

lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.

4. Shake and wipe off excess fluid before

re-assembling the fader.

PL-SK1

Two way input toggle switch

3PL-SK1

Three way input toggle
switch with FLASH™

LF-SK5

Channel input fader

CF-SK5

Crossfader

PP-SK5

PROTEKT™ panel

PS-13US

US Power Supply (110v)

PS-13EU

European Power Supply (220v)

PS-13UK

UK only Power Supply (240v)

ROTATING I NST RU C TI O NS

1 . Remove the PROTEKT™ panel

2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)

3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes

R E PLAC I N G I NST RU C TI O NS

1. Remove the PROTEKT™ panel

2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)

3. Remove the switch assembly and dis-
connect the cable coming from the mixer.

4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.