Roland 04672434 Manuale Utente
63
Chapter 5 Using MIDI
Chapter 5
Selecting How the Hold Functions
(HOLD TYPE)
(HOLD TYPE)
This selects the Hold function type when the controller set with the
HOLD CTL parameter (p. 59) is adjusted.
HOLD CTL parameter (p. 59) is adjusted.
1.
Follow Steps 1–2 in “Setting the Transmission
Mode (MODE)” (p. 61) to display the BASS TO
MIDI screen.
Mode (MODE)” (p. 61) to display the BASS TO
MIDI screen.
2.
Press PAGE [
] to display Page 1.
3.
Use [F1] (SELECT) or the F1 knob to select
MONO.
MONO.
4.
Adjust the setting with [F4] (SELECT) or the F4
knob.
knob.
• HOLD 1
The Note On messages are held when the Hold function is
switched on with the controller.
switched on with the controller.
If the Hold function remains on as you continue to play the
strings, each successive Note On message is held, and when a
Note message is already being played from the same string,
the previous Note message is cancelled, and the next Note On
message is held. This allows you to prevent any interruption
in the sounds, even sounds from releasing the strings over the
frets.
strings, each successive Note On message is held, and when a
Note message is already being played from the same string,
the previous Note message is cancelled, and the next Note On
message is held. This allows you to prevent any interruption
in the sounds, even sounds from releasing the strings over the
frets.
• HOLD 2
The Note On messages are held when the Hold function is
switched on with the controller.
switched on with the controller.
However, subsequent Note On messages are not output if you
continue to play the instrument with the Hold effect left on.
continue to play the instrument with the Hold effect left on.
• HOLD 3
The Note On messages are held when the Hold function is
switched on with the controller.
switched on with the controller.
If the Hold function remains on as you continue to play the
strings, Note On messages for strings other than the one
already being held can be output, but they are not held.
strings, Note On messages for strings other than the one
already being held can be output, but they are not held.
Outputting Control Changes by
Operating the Controllers (CC)
Operating the Controllers (CC)
You can operate the panel knobs and pedals to output Control
Change messages.
Change messages.
There are two different settings.
1.
Follow Steps 1–2 in “Setting the Transmission
Mode (MODE)” (p. 61) to display the BASS TO
MIDI screen.
Mode (MODE)” (p. 61) to display the BASS TO
MIDI screen.
2.
Press PAGE [
] [
] to display Page 2.
3.
Use [F1] (SELECT) or the F1 knob, or [F4]
(SELECT) or the F4 knob, to select the
controller you want to set.
(SELECT) or the F4 knob, to select the
controller you want to set.
4.
Use [F2] (SELECT) or the F2 knob, or [F5]
(SELECT) or the F5 knob, to select the Control
Change number you want to output.
(SELECT) or the F5 knob, to select the Control
Change number you want to output.
Off, CC #1–#31, CC #64–#95
SRC
Controller
GK VOL
GK-3B Volume knob
GK S1
GK-3B DOWN/S1 Switch
GK S2
GK-3B UP/S2 Switch
CTL1
Control Button 1
CTL2
Control Button 2
EXP PEDAL
External Expression Pedal
CTL3
External Footswitch 3
CTL4
External Footswitch 4
D BEAM V
D BEAM Height
D BEAM H
D BEAM Left-Right
RIBBON ACT
Ribbon Controller Touch
RIBBON POS
Ribbon Controller Touch Position
FC-300 EXP1
FC-300’s EXP PEDAL 1
FC-300 EXPSW1
FC-300’s EXP PEDAL SW1
FC-300 EXP2
FC-300’s EXP PEDAL 2
FC-300 EXPSW2
FC-300’s EXP PEDAL SW2
FC-300 CTL1
FC-300’s CTL1
FC-300 CTL2
FC-300’s CTL2
FC-300 E3/C3
FC-300’s External Expression Pedal 3,
External Footswitch 3
External Footswitch 3
FC-300 CTL4
FC-300’s External Footswitch 4
FC-300 E4/C5
FC-300’s External Expression Pedal 4,
External Footswitch 5
External Footswitch 5
FC-300 CTL6
FC-300’s External Footswitch 6
FC-300 E5/C7
FC-300’s External Expression Pedal 5,
External Footswitch 7
External Footswitch 7
FC-300 CTL8
FC-300’s External Footswitch 8
VB-99_e.book 63 ページ ２００８年８月１８日 月曜日 午後１時１０分