Celestron 80GTL Manuale Utente
10
U
U
s
s
i
i
n
n
g
g
y
y
o
o
u
u
r
r
S
S
o
o
l
l
a
a
r
r
F
F
i
i
l
l
t
t
e
e
r
r
Solar observing is one of the most rewarding forms of celestial observations. Yet, because the Sun is so bright, special
precautions must be taken to ensure your safety and protect your equipment. Therefore, read these instructions through
completely BEFORE you attempt to use your solar filter.
precautions must be taken to ensure your safety and protect your equipment. Therefore, read these instructions through
completely BEFORE you attempt to use your solar filter.
A Word of Caution
Never look through the StarPointer finderscope when pointed at the Sun.
About the Filter
The Celestron AstroSolar™ solar filter by Baader allows direct observations of the Sun in complete safety. The filter, which
transmit .00001% of the Sun’s visible light, allows you to see the outer atmosphere of the Sun including such features as
sunspots, granules and faculae. The material used to make these filters is a precision engineered, high-strength polymer that is
ion implanted and metallized with a tough, neutral color layer on both sides of the film.
transmit .00001% of the Sun’s visible light, allows you to see the outer atmosphere of the Sun including such features as
sunspots, granules and faculae. The material used to make these filters is a precision engineered, high-strength polymer that is
ion implanted and metallized with a tough, neutral color layer on both sides of the film.
The Appearance
One of the first things you may notice when you remove your solar filter from the box is that the film is slightly wrinkled. This
is the way the filter is supposed to look. The best resolution is obtained when the material is slightly relaxed or wrinkled.
is the way the filter is supposed to look. The best resolution is obtained when the material is slightly relaxed or wrinkled.
Installation and Use
Before installing the solar filter, you should always inspect the surface of the filter
for holes or other damage. To inspect the filter, hold it up to a bright light source
(other than the Sun) like a white wall reflecting sunlight or a patch of blue sky away
from the sun. Look for any light that may be passing through the filter. If any
light is visible, the filter should NOT be used.
for holes or other damage. To inspect the filter, hold it up to a bright light source
(other than the Sun) like a white wall reflecting sunlight or a patch of blue sky away
from the sun. Look for any light that may be passing through the filter. If any
light is visible, the filter should NOT be used.
To install the filter, point your telescope away from the Sun and remove the lens
cap. Now, place the solar filter over the front lens or opening of the telescope. Push
the filter cell until the inside of the filter cell is flush against the end of the tube. The
filter should be tight enough so that it will NOT fall off when the telescope is
pointed toward the ground.
cap. Now, place the solar filter over the front lens or opening of the telescope. Push
the filter cell until the inside of the filter cell is flush against the end of the tube. The
filter should be tight enough so that it will NOT fall off when the telescope is
pointed toward the ground.
Once the solar filter is securely in place you are ready for your first look. To do so,
point the telescope in the general direction of the Sun. Now, look at the shadow of
the telescope tube, which will indicate how close you are to the Sun. Look closely at the shadow cast by the StarPointer
finderscope. When you see light shining through the StarPointer’s sight tube you are approaching the Sun. The more elongated
the light, the farther away from the Sun you are pointing. When the light is circular, you should be pointing directly at the Sun.
Look through a low power eyepiece to see if the solar image is there. If not, slowly sweep around until the sun comes into the
field.
point the telescope in the general direction of the Sun. Now, look at the shadow of
the telescope tube, which will indicate how close you are to the Sun. Look closely at the shadow cast by the StarPointer
finderscope. When you see light shining through the StarPointer’s sight tube you are approaching the Sun. The more elongated
the light, the farther away from the Sun you are pointing. When the light is circular, you should be pointing directly at the Sun.
Look through a low power eyepiece to see if the solar image is there. If not, slowly sweep around until the sun comes into the
field.
Cleaning and Storage
To clean the filter, use a photographic cleaning brush to remove dust and other debris. Never rub the filter. Be sure that when
handling your solar filter not to touch the filter itself. When not in use, store your filter in its box. Place the box in a dry, warm
environment that is relatively dust free. Moisture on the filter can and will degrade the performance. Do not use the filter if
AstroSolar film is punctured in any way.
handling your solar filter not to touch the filter itself. When not in use, store your filter in its box. Place the box in a dry, warm
environment that is relatively dust free. Moisture on the filter can and will degrade the performance. Do not use the filter if
AstroSolar film is punctured in any way.
For tips on viewing the Sun through your filter, see the Celestial Observing section of this manual.
AstroSolar Filter
Material
Filter Cell
F
F
i
i
g
g
u
u
r
r
e
e
2
2
-
-
7
7
–
–
S
S
o
o
l
l
a
a
r
r
F
F
i
i
l
l
t
t
e
e
r
r