Sony 443 Dépliant

SRF-M85V_U  [US]     2-585-437-21(1)

(See Fig. B– )

Slide the connector onto the unit until you hear a click.

Unwind and straighten the wraparound arm band.

To more easily straighten the band, slightly bend the tip of the band in the
opposite direction.

Hold the body of the unit and attach the straightened band to your
arm.

The band will wind by itself.

Tighten the band with the rubber belt.

B

While holding down “PUSH RELEASE” (1), slide the connector to remove the
arm band (2).

The arm band can be attached either on left or right arm by changing up side
down. The unit can also be removed with the arm band attached on your arm, as
instructed above.

B

Move the velcro fastener to the proper position.

Remove the rubber belt from the unit and clean them.

B

• Avoid bending the wraparound band forcibly in the opposite direction. It may

break.

• The straightened band will wind easily when you touch or wiggle it. Be sure to

treat it carefully.

When you slide 

in the direction of the arrow, “-” appears in the

display. All the other buttons on the radio will become inoperative.
This function prevents the radio from being unintentionally turned on, or the
radio frequency from being accidentally changed.

To cancel HOLD, slide 

in the opposite direction of the arrow so that

“ -” disappears.

The display will flash “AM 12:00” when the battery is first inserted.

Press DISPLAY repeatedly to select the clock mode when the
clock mode is not on.

Hold down ENTER for more than 2 seconds.

The beep sounds and the hour flashes in the display.

Press TUNE/TIME SET + or – until the correct hour appears in
the display.

Each press changes the digit(s) by one.
When you keep the button pressed, the digit(s) change rapidly.

Press ENTER.

The beep sounds and the minute starts to flash.
Repeat step 

 to set the minute. After setting the minute,

press 

again. The two beeps sound and the clock

starts from 0 seconds.

• One you start setting the clock, you must perform each step within 65 seconds,

or the clock setting mode will be cancelled.

• 12-hour system: “AM 12:00” = midnight, “PM 12:00” = noon.

The AM channel step differs depending on areas. The channel step of this unit is
factory-set to 10 kHz. Change the settings as shown below to be able to listen to
the radio.

North and South American countries/regions

10 kHz

Other countries/regions

9 kHz

When the AM channel step is changed, the preset stations for AM will be
initialized.

Press POWER to turn off the power.

Press DISPLAY repeatedly to select the clock mode when the
clock mode is not on.

While holding down TUNE/TIME SET + or –, keep pressing
MODE for more than 5 seconds.

Two short beeps sound, and the AM channel step will be changed.
“AM 9” (or “AM 10”) is displayed for about 2 seconds.
If you proceed to step 

 again, the channel step changes again.

B

You can use this unit as a radio, clock, stopwatch, pitch timer or countdown
timer.
The functions of clock, stopwatch, pitch timer, countdown timer are available
even if the power is off.

Press 

to select a function mode.

Each function mode can be selected as follows:

Stopwatch

Radio frequency

Clock

Pitch timer

Countdown timer

* Selected only when the power is on.

Connect the headphones to the i (headphones) jack.

Press POWER to turn on the radio.

“

” appears in the display.

If “

” is displayed, press MODE so that “

” disappears.

Pressing 

will switch over between manual tuning mode and preset

tuning mode.

Press BAND to select the band.

Each press changes the band as follows:

AM

FM

TV

WEATHER

Press TUNE/TIME SET + or – to select the desired frequency.

If you hold down 

or

, the frequency or channel

changes rapidly.
When the frequency matches the broadcast frequency, the broadcast will be
received.

Adjust the volume using VOL.

To turn off the radio, press POWER.

: Extend the headphones cord which

functions as the TV/WEATHER/FM
antenna (See Fig. C-

).

: Rotate the unit horizontally for

optimum reception. A ferrite bar
antenna is built-in the unit (See
Fig.C-

).

Set 

to 

if interference is

prevalent and reception is too strong. Under normal
conditions, set it to 

.

Press MEGA BASS.

“

” indication appears in the display when the MEGA BASS function is on.

The MEGA BASS function intensifies the bass sound for richer quality audio
reproduction.

You can preset up to 5 stations each for TV, WEATHER and AM, and 15
stations for FM. Also, you can delete the preset station whether it is factory-set or
preset by yourself.

Follow steps 1 to 5 in “Playing the Radio” and manually tune in to
the station you wish to preset.

Hold down ENTER until the preset number flashes.

If there is a preset number that has no preset station, that preset number
flashes.
When all the preset numbers are set to certain stations, the following occurs:
• Initialized (factory-set): “

” flashes and “

” appears.

• After tuning in a preset station: The next preset number after the one last

preset flashes and “

” appears.

Press TUNE/TIME SET + or – to select the number you wish to
preset, then press ENTER.

When you select the preset number using 

or

, “

”

appears if that number has a preset station. If it has no preset station, only the
number flashes and “

” does not appear.

When you press 

, the selected preset number lights up in the display.

: Display window when you preset FM 90.0 MHz in preset

number 2.

To preset another station, repeat these steps.
To change the preset station, preset a new station. The previous station will
be canceled.

To cancel the presetting mode, press 

.

If you do not press 

or

, or 

within 65 seconds, the

preset tuning mode will be canceled.

Press POWER to turn on the radio.

Press MODE so that “

” and preset number appear.

Select the band with BAND.

Press TUNE/TIME SET + or – to select the desired preset
number.

Adjust the volume using VOL.

To turn off the radio, press POWER.

If you hold down 

for more than 2 seconds, the unit enters the preset

station deleting mode. Press 

again to return to the previous mode.

Follow steps 1 and 2 in “Tuning in to a Preset Station”.

Select the band with BAND.

Press TUNE/TIME SET + or – to select the preset number to be
deleted.

Hold down MODE for more than 2 seconds until “

”, “

” and

the preset number flash.

While the letters and the preset number are flashing, press
ENTER.

The station set to the preset number just before the deleted station will be
displayed.
To delete other stations, repeat steps 

 to 

.

If all the preset stations are deleted, “

” appears in the display.

To cancel deleting, press 

while “

”, “

” and the preset number

are flashing.

The stopwatch can time up to 99 hours 59 minutes and 59.99 seconds, in 1/100-
second increments.

Press DISPLAY to select the stopwatch.

“

” flashes in the display.

Press START/STOP to start.

The display shows the elapsed time.

Press START/STOP to stop.

To reset to zero, press 

when the stopwatch is in the stop

status.

The stopwatch comes with two display modes. To switch to the hour-minute-
second display, press 

.

To switch to the minute-second-split second display, press 

again.

When the count time exceeds “59:59 99” during the minute-second-split
second display, the display switches to the hour-minute-second display.

To switch to the other modes during counting, press 

.

“

” stops flashing if changed to other mode while the stopwatch counts

down.

To listen to the radio while the stopwatch is running, press 

. The

display will switch to the radio frequency for a few seconds.

To display the current split time, press 

while the stopwatch is

running. “

” flashes in the display.

The stopwatch keeps counting during the display.

To return to the count display, press 

again while the split time is

being displayed.

D

*

1

*

2

i

*

2

C

The pitch timer allows setting the timer with an identical length of time
repeatedly. The functions of the radio, the stopwatch, and the countdown timer
are available even while the pitch timer is being used.

Press DISPLAY to select the pitch timer.

“

” flashes in the display.

Hold down ENTER for more than 2 seconds.

The beep sounds and the countdown duration flashes in
the display.

Press TUNE/TIME SET + or – to set the desired countdown
duration for the pitch timer.

The countdown duration can be set from 1 second to 59 minutes 59 seconds,
in 1-second increments.

Press ENTER.

The beep sounds and the number of times flashes in the
display.

Press TUNE/TIME SET + or – to set the desired number of
times.

The number of times can be set up to 99.

Press ENTER.

The two beeps sound and the number of times stops flashing.

Press START/STOP.

Countdown starts. After the preset countdown duration, the two beeps sound
three times.

When the last pitch timer setting is finished, the display switches to the pitch
timer display even in another display mode and a long beep sounds, and then
returns to the previous display.
To stop the long beep, press any button.

To pause the countdown on the pitch timer, press 

while counting

down.
At this time, the countdown is reset by pressing 

. The display will

show the set-up countdown duration and number of times.

To switch to the other modes, press 

.

“

” stops flashing if changed to other mode while the pitch timer counts

down.

You can use the built-in countdown timer to turn off the radio automatically after
a preset duration.

Press DISPLAY to select the countdown timer.

“

” flashes in the display.

Hold down ENTER for more than 2 seconds.

The beep sounds, and the countdown duration starts flashing.

Press TUNE/TIME SET + or –  to set the desired countdown
duration for the timer.

The countdown duration can be set from 1 minute to 2 hours, in 1-minute
increments.

Press ENTER.

The two beeps sound and the countdown duration stops flashing.

Press START/STOP.

Countdown starts. The radio is automatically turned on when the radio is off.
After the preset countdown duration, the four beeps sound five times and the
radio is turned off.
To stop the beeps, press any button.

To turn off the radio before the preset time, press 

.

To pause the countdown on the countdown timer, press 

while

counting down.
At this time, the countdown is reset by pressing 

. The display will

show the set-up countdown duration.

To switch to the other modes, press 

.

“

” stops flashing if changed to other mode while the countdown timer

counts down.

(See Fig. D)

Use the belt clip when attaching the unit to your belt.

*

1