Toshiba 3520C Manuale Utente
Toshiba e-STUDIO3520c
Copyright © 2008 BERTL Inc.
All Rights Reserved. The license under which this document is made available and applicable law prohibit any reproduction or further transmission of any portion of this document. This
document may only be viewed electronically through the www.BERTL.com Web site and may not be stored in electronic or hard copy format. Any reproduction of trademarks is strictly
prohibited. BERTL accepts no responsibility for any inaccuracies or omissions contained in this document.
document may only be viewed electronically through the www.BERTL.com Web site and may not be stored in electronic or hard copy format. Any reproduction of trademarks is strictly
prohibited. BERTL accepts no responsibility for any inaccuracies or omissions contained in this document.
Page 27
August 2008
Toshiba e-STUDIO3520c
www.BERTL.com
ROUTINE MAINTENANCE
Workgroup devices sold through retail and traditional IT
distribution outlets usually are maintained by office workers
who change the all-in-one cartridge units that encase the
entire imaging system, including the toner cartridge (or the
ink cartridges employed by ink-jet imaging systems). Units
sold through resellers and dealers are usually maintained
by office workers and/or trained service engineers. While
separate long-life parts are more complex to install (i.e.,
separate toner cartridges, imaging drums, transfer belts),
they tend to cost less than low- yield, all-in-one
alternatives.
Toner or Ink Replacement
Changing the toner, imaging cartridge or ink cartridge is a
necessary task that is traditionally is avoided by some for
fear of toner dust or ink leaking on clothing or hands, or the
fear that it might be too complicated. However, most units
today offer clean replacement of toner or ink supplies, and
there is very little risk of toner or ink leakage. Usually the
replacement process is typically easy.
Clearing Media Misfeeds
The main issue that office users attempt to avoid is the
removal of an occasional media misfeed. As a general
rule, the faster a device engine, and the more media
handling and finishing options it has, the more complex is
the process of removing media misfeeds.
Common media-misfeed sources involve the duplex unit
and poor loading of media supplies. The position of the
duplex unit may be a major factor in the removal of many
media misfeeds. How easy or difficult it is to load media
supplies can also be a factor in the overall number of
misfeeds that may occur.
Loading Media
It goes without saying that loading media should be as
easy as possible, but sometimes that is not the case.
Among the factors that affect ease-of-use are:
Workgroup devices sold through retail and traditional IT
distribution outlets usually are maintained by office workers
who change the all-in-one cartridge units that encase the
entire imaging system, including the toner cartridge (or the
ink cartridges employed by ink-jet imaging systems). Units
sold through resellers and dealers are usually maintained
by office workers and/or trained service engineers. While
separate long-life parts are more complex to install (i.e.,
separate toner cartridges, imaging drums, transfer belts),
they tend to cost less than low- yield, all-in-one
alternatives.
Toner or Ink Replacement
Changing the toner, imaging cartridge or ink cartridge is a
necessary task that is traditionally is avoided by some for
fear of toner dust or ink leaking on clothing or hands, or the
fear that it might be too complicated. However, most units
today offer clean replacement of toner or ink supplies, and
there is very little risk of toner or ink leakage. Usually the
replacement process is typically easy.
Clearing Media Misfeeds
The main issue that office users attempt to avoid is the
removal of an occasional media misfeed. As a general
rule, the faster a device engine, and the more media
handling and finishing options it has, the more complex is
the process of removing media misfeeds.
Common media-misfeed sources involve the duplex unit
and poor loading of media supplies. The position of the
duplex unit may be a major factor in the removal of many
media misfeeds. How easy or difficult it is to load media
supplies can also be a factor in the overall number of
misfeeds that may occur.
Loading Media
It goes without saying that loading media should be as
easy as possible, but sometimes that is not the case.
Among the factors that affect ease-of-use are:
• The user should be able to load an entire ream (500
sheets) in a single step.
• Mechanisms such as corner separators and ramps in
the media drawer can impede loading media.
The most critical factor involved in ease-of-loading media is
automatic media-size detection. Ultimately, the device
should be able to recognize the new media size and reflect
it on its control panel/touch screen and across the network
in print drivers and printer-management software. Without
automatic media-size detection, users must remember to
program-in the new media size—something they often
neglect to do, or do incorrectly. This can result in jobs
printed on the wrong media size, backed-up job logs, etc.
automatic media-size detection. Ultimately, the device
should be able to recognize the new media size and reflect
it on its control panel/touch screen and across the network
in print drivers and printer-management software. Without
automatic media-size detection, users must remember to
program-in the new media size—something they often
neglect to do, or do incorrectly. This can result in jobs
printed on the wrong media size, backed-up job logs, etc.
LOADING MEDIA
Paper Loading Checklist
Maximum media weight from all media sources?
No
Drop-in loading of a full ream of paper?
Yes
Corner separators in paper trays?
No
Spring-loaded ramps in paper trays?
No
Geared media size side guides?
No
Captured rear media guide?
Yes
Automatic paper size detection?
No
Both tray 1 and tray 2 can each hold 550 sheets of 20 lb. Bond
/80 gsm or 500 sheets (105 gsm or 28 lbs bond media (in from
5.5"x8.5"/A5-R up to 11"X17"/A3).
/80 gsm or 500 sheets (105 gsm or 28 lbs bond media (in from
5.5"x8.5"/A5-R up to 11"X17"/A3).
In order to adjust the paper drawers, the user must unlock the
drawer by squeezing the lock on the top left. Once unlocked, the
user squeezes the green lever on the bottom right and then slides
the guide into place.
drawer by squeezing the lock on the top left. Once unlocked, the
user squeezes the green lever on the bottom right and then slides
the guide into place.