NEC MD21GS-3MP Manuale Utente
2
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to
CAN/CSA C22.2 No. 601.1.
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to
CAN/CSA C22.2 No. 601.1.
FCC Information
1. Use the attached specified cables with the MD21GS-3MP grayscale display so as not to interfere
1. Use the attached specified cables with the MD21GS-3MP grayscale display so as not to interfere
with radio and television reception.
(A) Please use the supplied power cord or equivalent to ensure FCC compliance.
(B) Please use the supplied shielded video signal cable, DVI-D to DVI-D cable.
Use of other cables and adapters may cause interference with radio and television reception.
2. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult your dealer or an experienced radio/TV technician for help.
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is
available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-
00345-4.
additional suggestions. The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is
available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-
00345-4.
Declaration of the Manufacturer
We hereby certify that the grayscale monitor MD21GS-3MP is in compliance with Council Directive
93/42/EEC:
We hereby certify that the grayscale monitor MD21GS-3MP is in compliance with Council Directive
93/42/EEC:
– EN 60601-1
– EN 60601-1-2
– EN 61000-3-2
– EN 61000-3-3
– EN 60601-1-2
– EN 61000-3-2
– EN 61000-3-3
and marked with CE.
NEC-Mitsubishi Electric Visual, Systems Corporation, 4-13-23, Shibaura, Minato-Ku, Tokyo 108-
0023, Japan
NEC-Mitsubishi Electric Visual, Systems Corporation, 4-13-23, Shibaura, Minato-Ku, Tokyo 108-
0023, Japan
MD21GS3MPquickstart.p65
7/22/04, 9:52 AM
2