Seagate ST2000NC000 Manuale Utente
Constellation CS Serial ATA Product Manual, Rev. C
30
5.3.1
Identify Device command
The Identify Device command (command code EC
H
) transfers information about the drive to the host following power up. The
data is organized as a single 512-byte block of data, whose contents are shown on page 28. All reserved bits or words should
be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
The following commands contain drive-specific features that may not be included in the SATA specification.
Word
Description
Value
0
Configuration information:
Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
0C5A
H
1
Number of logical cylinders
16,383
2
ATA-reserved
0000
H
3
Number of logical heads
16
4
Retired
0000
H
5
Retired
0000
H
6
Number of logical sectors per logical track: 63
003F
H
7–9
Retired
0000
H
10–19
Serial number: (20 ASCII characters, 0000
H
= none)
ASCII
20
Retired
0000
H
21
Retired
0000
H
22
Obsolete
0000
H
23–26
Firmware revision
(8 ASCII character string, padded with blanks to end of string)
(8 ASCII character string, padded with blanks to end of string)
xxxx
27–46
Drive model number:
(40 ASCII characters, padded with blanks to end of string)
(40 ASCII characters, padded with blanks to end of string)
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16)
8010
H
48
Reserved
0000
H
49
Standard Standby timer, IORDY supported and may be disabled
2F00
H
50
ATA-reserved
0000
H
51
PIO data-transfer cycle timing mode
0200
H
52
Retired
0200
H
53
Words 54–58, 64–70 and 88 are valid
0007
H
54
Number of current logical cylinders
xxxx
H
55
Number of current logical heads
xxxx
H
56
Number of current logical sectors per logical track
xxxx
H
57–58
Current capacity in sectors
xxxx
H
59
Number of sectors transferred during a Read Multiple
or Write Multiple command
or Write Multiple command
xxxx
H
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors,
137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field and the
actual number of user-addressable LBAs specified in words 100-103. This is
required for drives that support the 48-bit addressing feature.
(see Section 2.2 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors,
137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field and the
actual number of user-addressable LBAs specified in words 100-103. This is
required for drives that support the 48-bit addressing feature.
0FFFFFFFh*
62
Retired
0000
H
63
Multiword DMA active and modes supported
(see note following this table)
(see note following this table)
xx07
H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003
H
65
Minimum multiword DMA transfer cycle time per word (120 nsec)
0078
H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
(120 nsec)
0078
H
67
Minimum PIO cycle time without IORDY flow control (240 nsec)
0078
H