Black Box LBPS310A-KIT Manuale Utente
10/100Base-TX Hardened PoL/PoE Ethernet Extender
User’s Manual
1
Quick Start Guide
This quick start guide describes how to install and use the Hardened
Ethernet Extender. This is the Hardened Ethernet Extender of choice for
harsh environments constrained by space.
Ethernet Extender. This is the Hardened Ethernet Extender of choice for
harsh environments constrained by space.
Installation
Transmitter: This is a PoL (Power over Link) transmitter. Data and power can be
delivered at the same time through one pair copper wire to turn on and communicate with
a Receiver via an RJ-11 phone jack or a 2-pin Terminal Block interface.
Receiver: This is a PoL (Power over Link) Receiver. The Receiver can be powered either
by a Transmitter through one pair copper wire or power supply. The Ethernet port
supports IEEE802.3at PoE/PSE for fulfilling PoE/PD application.
delivered at the same time through one pair copper wire to turn on and communicate with
a Receiver via an RJ-11 phone jack or a 2-pin Terminal Block interface.
Receiver: This is a PoL (Power over Link) Receiver. The Receiver can be powered either
by a Transmitter through one pair copper wire or power supply. The Ethernet port
supports IEEE802.3at PoE/PSE for fulfilling PoE/PD application.
<Warning>
∞ Remove the device power before installation.
∞ Remove the device power before installation.
∞ Remove the device power before any I/O and DIP switch configuration.
∞ Do not connect the Transmitter and the Receiver to the same power source.
Power loops back through the PoL linked via copper wire may damage devices.
PoL (Power over Link) Mode Enable Installation
∞ Ensure all power sources are disconnected from Transmitter and Receiver.
∞ Ensure that the Transmitter PoL (Power over Link) DIP switch is in On position (Up
position).
∞ Set the Transmitter Type DIP switch to Per (Performance, Up position) for better Line
Speed (but poor noise immunity). Or set the Transmitter’s Type DIP switch to Std
(Standard, Down position) for standard Line Speed (but better noise immunity).
(Standard, Down position) for standard Line Speed (but better noise immunity).
∞ Check if Receiver Mode is set to Rmt on DIP switch (Remote, Up position).
∞ Connect one end of the one pair copper wire to RJ-11 phone jack or 2-pin Terminal
Block interface of the Transmitter and the other end to RJ-11 phone jack or 2-pin
Terminal Block interface of the Receiver.
Terminal Block interface of the Receiver.
∞ Connect a power source to Transmitter.
∞ Data and power can be delivered from Transmitter, and at the same time through
one pair of copper wire to turn on and communicate with Receiver.
<Note> The equipment is designed for building installation and not intended to be
connected to exposed (outside plant) networks, including campus environment or
equivalent.
PoL (Power over Link) Mode Disable Installation
∞ For longer distance (e.g. over 1.4km) extension applications, the Receiver may not
be able to receive power from the Transmitter. A separate power supply may be
used on the Receiver.
used on the Receiver.
∞ Ensure all power sources are disconnected from the Transmitter and the Receiver.
∞ Ensure that the Transmitter PoL (Power over Link) DIP switch is in Off position
(Down position).
∞ Set the Transmitter Type DIP switch to Per (Performance, Up position) for better Line
Speed (but poor noise immunity). Or set the Type DIP switch of Transmitter to Std
(Standard, Down position) for standard Line Speed (but better noise immunity).
(Standard, Down position) for standard Line Speed (but better noise immunity).
∞ Connect the power source to Transmitter.
∞ Check if the Receiver Mode is set to Rmt on DIP switch (Remote, Up position).
∞ Connect the power source to the Receiver.