Manualsbrain.com
  1. Manuali
  2. Marche
  3. Timex
  4. 75328T
  5. Manuale Utente

Timex 75328T Manuale Utente

Scarica
Pagina di 4
SETTING THE CLOCK MANUALLY
  
Back of Clock
“Set” to confirm 
manual settings
Down 
Arrow
SET
Up 
Arrow
5
4
The wireless temperature sensor MUST BE PLACED OUTDOORS to capture and relay the 
outdoor temperature to the clock display unit. You may place your wireless temperature 
sensor outside up to 100 feet (30m) from the clock, as shown.
The main unit has a signal reception icon near the outdoor temperature display area.  If 
there are a low number of “bars” present, you may experience no temperature display 
(“--”) or inaccuracy.  In either case, you may need to relocate one of both of the units.  If 
most or all 4 of the bars are present, wireless reception is good and no action is required.
Placement of the Clock:
Place the clock in an area free of dirt and dust. To help ensure an accurate 
indoor temperature measurement, be sure to place the main unit out of 
direct sunlight, and away from any heat sources or vents in your home.  
This clock may be hung on a wall using the integrated wall-hanging hole, 
or you may place the unit on a tabletop or other flat surface using the 
swing-out stands.
Placement of the Outdoor Sensor:
Wireless Signal Reception Icons
The sensor is water resistant and is designed 
for outdoor use.  However, to extend the life 
of the product, place it in an area protected 
from harsh weather elements. To ensure an 
accurate temperature reading, be sure the 
sensor is out of direct sunlight and away from 
any heat sources.
Strong
Reception
NO
Reception
100’ Feet
a)  Press and 
HOLD the SET button until you see the selection of seven time zones
 Then 
RELEASE.
b)  Press the UP (
s
) ARROW 
repeatedly until you reach your time zone,
 
then press 
SET and release.
a)  Press the UP (
s
) ARROW to turn 
DST (Daylight Saving Time) function on or off. 
 
Press “SET” to confirm and 
RELEASE.
b) The 
HOUR will flash
c) The 
MINUTE will flash
d) The 
YEAR will flash
e) The 
MONTH will flash
f) The 
DATE will flash
e) The 
°F will flash
Press “SET”
to confirm
Press “SET”
to confirm
Press “SET”
to confirm
Press “SET”
to confirm
Press “SET”
to confirm
Press “SET”
to confirm
Press the UP (
s
) ARROW repeatedly, 
until the correct hour (AM or PM) is 
displayed.
Press the UP (
s
) ARROW repeatedly, 
until the correct minute is displayed.
Press the UP (
s
) ARROW repeatedly, 
until the correct year is displayed.
Press the UP (
s
) ARROW repeatedly, 
until the correct month is displayed.
Press the UP (
s
) ARROW repeatedly, 
until the correct date is displayed.
Press the UP (
s
) ARROW to change
between
 °F and °C.
 
Press the UP (
s
) ARROW to or DOWN (
t
) ARROW buttons 
to turn 
 
OFF Atomic signal. This will stop the clock from searching for the Atomic 
 
radio signal.
NOTE: You do NOT need to turn off the atomic clock to set the time manually. Once the clock receives the signal, it will adjust the 
clock accordingly. However, you may choose to deactivate the atomic clock feature completely if you prefer to manually control 
the clock or if you live in a remote area that does not readily receive the atomic signal. As long as the atomic clock is ON, it will 
automaticlly adjust itself to the correct time, overriding your manual setting.
1) SETTING YOUR TIME ZONE
3) SETTING THE CLOCK & CALENDAR
2) TURNING ATOMIC CLOCK FEATURE ON/OFF
DAY OF THE WEEK AND MOON PHASE WILL UPDATE AUTOMATICALLY AS YOU SET THE DATE