MiTAC 8050D Manuale Utente
8050
8050
D N/B Maintenance
D N/B Maintenance
90
Processor Interface Signals (Continued)
Signal Name
Type
Description
CPUPWRGD
OD
CPU Power Good: This signal should be connected to the
processor’s PWRGOOD input. To allow for Intel ® SpeedStep™
technology support, this signal is kept high during an Intel
SpeedStep technology state transition to prevent loss of processor
context. This is an open-drain output signal (external pull-up
resistor required) that represents a logical AND of the ICH4’s
PWROK and VGATE / VRMPWRGD signals.
processor’s PWRGOOD input. To allow for Intel ® SpeedStep™
technology support, this signal is kept high during an Intel
SpeedStep technology state transition to prevent loss of processor
context. This is an open-drain output signal (external pull-up
resistor required) that represents a logical AND of the ICH4’s
PWROK and VGATE / VRMPWRGD signals.
DPSLP#
O
Deeper Sleep: This signal is asserted by the ICH4 to the processor.
When the signal is low, the processor enters the Deeper Sleep state
by gating off the processor Core clock inside the processor. When
the signal is high (default), the processor is not in the Deeper Sleep
state. This signal behaves identically to the STP_CPU# signal, but
at the processor voltage level.
When the signal is low, the processor enters the Deeper Sleep state
by gating off the processor Core clock inside the processor. When
the signal is high (default), the processor is not in the Deeper Sleep
state. This signal behaves identically to the STP_CPU# signal, but
at the processor voltage level.
SMBus Interface Signals
Signal Name
Type
Description
SMBDATA
I/OD
SMBus Data: External pull-up is required.
SMBCLK
I/OD
SMBus Clock: External pull-up is required.
SMBALERT#/
GPIO[11]
GPIO[11]
I
SMBus Alert: This signal is used to wake the system or generate
SMI#. If not used for SMBALERT#, it can be used as a GPI.
SMI#. If not used for SMBALERT#, it can be used as a GPI.
System Management Interface Signals
Signal Name
Type
Description
INTRUDER#
I
Intruder Detect: Can be set to disable system if box detected open.
This signal’s status is readable, so it can be used like a GPI if the
Intruder Detection is not needed.
This signal’s status is readable, so it can be used like a GPI if the
Intruder Detection is not needed.
SMLINK[1:0]
I/OD
System Management Link: SMBus link to optional external
system management ASIC or LAN controller. External pull-ups are
required.
Note that SMLINK[0] corresponds to an SMBus Clock signal, and
SMLINK[1] corresponds to an SMBus Data signal.
system management ASIC or LAN controller. External pull-ups are
required.
Note that SMLINK[0] corresponds to an SMBus Clock signal, and
SMLINK[1] corresponds to an SMBus Data signal.
Real Time Clock Interface Signals
Signal Name
Type
Description
RTCX1
Special
Crystal Input 1: This signal is connected to the 32.768 kHz crystal.
RTCX2
Special
Crystal Input 2: This signal is connected to the 32.768 kHz crystal.
Other Clock Signals
Signal Name
Type
Description
CLK14
I
Oscillator Clock: Used for 8254 timers. It runs at 14.31818 MHz.
This clock is permitted to stop during S1-M (or lower) states.
This clock is permitted to stop during S1-M (or lower) states.
CLK48
I
48 MHz Clock: This clock is used to run the USB controller. It runs
at 48 MHz. This clock is permitted to stop during S1-M (or lower)
states.
at 48 MHz. This clock is permitted to stop during S1-M (or lower)
states.
CLK66
I
66 MHz Clock: This is used to run the hub interface. It runs at 66
MHz. This clock is permitted to stop during S1-M (or lower) states.
MHz. This clock is permitted to stop during S1-M (or lower) states.
Miscellaneous Signals
Signal Name
Type
Description
SPKR
O
Speaker: The SPKR signal is the output of counter 2 and is
internally “ANDed” with Port 61h bit 1 to provide Speaker Data
Enable. This signal drives an external speaker driver device, which
in turn drives the system speaker. Upon PCIRST#, its output state is
0.
NOTE: SPKR is sampled at the rising edge of PWROK as a
functional strap.
internally “ANDed” with Port 61h bit 1 to provide Speaker Data
Enable. This signal drives an external speaker driver device, which
in turn drives the system speaker. Upon PCIRST#, its output state is
0.
NOTE: SPKR is sampled at the rising edge of PWROK as a
functional strap.
RTCRST#
I
RTC Reset: When asserted, this signal resets register bits in the
RTC well and sets the RTC_PWR_STS bit (bit 2 in
GEN_PMCON3 register).
NOTES:
1. Clearing CMOS in an ICH4-based platform can be done by using
a jumper on RTCRST# or GPI, or using SAFEMODE strap.
Implementations should not attempt to clear CMOS by using a
jumper to pull VccRTC low.
2. Unless entering the XOR Chain Test Mode, the RTCRST# input
must always be high when all other RTC power planes are on.
RTC well and sets the RTC_PWR_STS bit (bit 2 in
GEN_PMCON3 register).
NOTES:
1. Clearing CMOS in an ICH4-based platform can be done by using
a jumper on RTCRST# or GPI, or using SAFEMODE strap.
Implementations should not attempt to clear CMOS by using a
jumper to pull VccRTC low.
2. Unless entering the XOR Chain Test Mode, the RTCRST# input
must always be high when all other RTC power planes are on.
5.3 Intel 82801DBM I/O Controller Hub 4 Mobile (ICH4-M)(7)
MiTac Secret
Confidential Document