Omron CS1W-RPT01 Manuale Utente
318
Error Log
Section 9-3
0117
Hex
Hex
Internal buffer full
Command block
Bits 0 to 7:
Bits 0 to 7:
Source node address
Bits 8 to 14:
Source Network address
Bit 15:
OFF
Response block
Bits 0 to 7:
Bits 0 to 7:
Destination node
address
address
Bits 8 to 14:
Destination Network
address
address
Bit 15:
ON
(1st byte: bits 8 to 15;
2nd byte, bits 0 to 7)
2nd byte, bits 0 to 7)
Increase number of
retries or reconfig-
ure system to distrib-
ute load.
retries or reconfig-
ure system to distrib-
ute load.
No
All
0118
Hex
Hex
Illegal packet discarded
Check for nodes
sending illegal
packets.
sending illegal
packets.
Yes
All
0203
Hex
Hex
EEPROM error
01 Hex:
Read error
02: Hex:
Write error
Read error
02: Hex:
Write error
01 Hex:
Data link
tables
02 Hex:
Network
parameters
03 Hex:
Routing
tables
Data link
tables
02 Hex:
Network
parameters
03 Hex:
Routing
tables
For CVM1 and CV-
series PLCs, check
that the PLC is not
protected.
series PLCs, check
that the PLC is not
protected.
Remake and set the
relevant data. If the
error occurs again for
the CVM1 and
CV-series, replace
the CPU Unit and for
the C200HX/HG/HE
PLCs, replace the
Controller Link Unit.
relevant data. If the
error occurs again for
the CVM1 and
CV-series, replace
the CPU Unit and for
the C200HX/HG/HE
PLCs, replace the
Controller Link Unit.
Yes
C200HX/HG/
HE, CV,
CQM1H
HE, CV,
CQM1H
0206
Hex
Hex
Number of participating nodes
decreased (local node still partic-
ipating)
decreased (local node still partic-
ipating)
Network
parameters
maximum
node
address
parameters
maximum
node
address
Number of
non-partici-
pating nodes
non-partici-
pating nodes
Check network
parameters, node
participation, cables,
and terminating
resistance.
parameters, node
participation, cables,
and terminating
resistance.
No
All
0207
Hex
Hex
Number of participating nodes
decreased (local node not partic-
ipating)
decreased (local node not partic-
ipating)
No
All
0208
Hex
Hex
Polling node changed
Address of
previous
polling node
previous
polling node
Address of
new polling
node
new polling
node
Check previous
polling node.
polling node.
No
All
0209
Hex
Hex
Inconsistent network parameter
00 Hex
Address of
polling node
polling node
Using the Controller
Link Support Soft-
ware, check network
parameters.
Link Support Soft-
ware, check network
parameters.
Yes
All
020C
Hex
Hex
Time out with token
00 Hex
Error status
(See note.)
(See note.)
Check network
parameters, node
participation, cables,
and terminating
resistance.
parameters, node
participation, cables,
and terminating
resistance.
No
All
0210
Hex
Hex
Communications controller send
error
error
00 Hex
Error status
(See note.)
(See note.)
Replace the Control-
ler Link Unit.
ler Link Unit.
Yes
All
0211
Hex
Hex
Duplicate address error
00 Hex
Local node
address
address
Reset so that each
node address is used
only once within the
same Network.
node address is used
only once within the
same Network.
No
All
0214
Hex
Hex
Node address setting error
Not specified
Check the node
address settings and
correct them.
address settings and
correct them.
Yes
CS/CJ,
CQM1H
CQM1H
Error
code
Contents
Detail code
Correction
Written to
EEPROM
Applicable
PLC
1st byte
2nd byte