Compatible Systems 5.4 Manuale Utente
Chapter 2 - IP Routing & Bridging
29
RIP 2 is more useful in a variety of environments and allows the use of vari-
able subnet masks on your network. It is also necessary for implementation
of “classless” addressing as accomplished with CIDR (Classless Inter
Domain Routing).
able subnet masks on your network. It is also necessary for implementation
of “classless” addressing as accomplished with CIDR (Classless Inter
Domain Routing).
It is recommended that RIP 2 be used on any segment where all routers can
use the same IP routing protocol. If one or more routers on a segment must
use RIP 1, then all other routers on that segment should also be set to use
RIP 1.
use the same IP routing protocol. If one or more routers on a segment must
use RIP 1, then all other routers on that segment should also be set to use
RIP 1.
•
If RIP 2 is selected with this pull-down menu, the router will send and/or
accept RIP 2 packets over this interface, and will then periodically update
its routing table with the information provided from these packets. On a
large network, an up-to-date routing table will enhance network perfor-
mance since the router will always be aware of the optimal path to use
when sending packets.
accept RIP 2 packets over this interface, and will then periodically update
its routing table with the information provided from these packets. On a
large network, an up-to-date routing table will enhance network perfor-
mance since the router will always be aware of the optimal path to use
when sending packets.
•
If RIP 1 is selected with this pull-down menu, the router will send and/or
accept RIP 1 packets, and will then periodically update its routing table
with the information provided from these packets.
accept RIP 1 packets, and will then periodically update its routing table
with the information provided from these packets.
•
If None is selected with this pull-down menu, the router will not be able
to update its routing table and will always direct traffic for addresses it
does not have a route for (addresses not on one of the networks connected
to its interfaces) to the “default router” defined in its IP Static Route
Dialog Box. It will then be the responsibility of the default router to
direct the packets to the correct address. For information on setting the
default router see the discussion of the IP Static Route Dialog Box later
in this chapter.
to update its routing table and will always direct traffic for addresses it
does not have a route for (addresses not on one of the networks connected
to its interfaces) to the “default router” defined in its IP Static Route
Dialog Box. It will then be the responsibility of the default router to
direct the packets to the correct address. For information on setting the
default router see the discussion of the IP Static Route Dialog Box later
in this chapter.
v Note: Some routers, in particular those designed to create very large
corporate backbones, may use other routing protocols such as OSPF (Open
Shortest Path First). These routers can simultaneously use RIP 1 (and in
some cases RIP 2) to communicate with smaller routers, or each of the
smaller routers can be set to use one of these backbone routers as their
default router.
corporate backbones, may use other routing protocols such as OSPF (Open
Shortest Path First). These routers can simultaneously use RIP 1 (and in
some cases RIP 2) to communicate with smaller routers, or each of the
smaller routers can be set to use one of these backbone routers as their
default router.
>
Update Method
WAN interfaces which are configured to provide “dial-on-demand” service
will bring a connection up (i.e. dial the other end) when there are network
packets which must be transferred over the link. Once a dial-on-demand
connection is up, network traffic passing across the link causes the inactivity
timer for the link to be reset, keeping the connection up.
will bring a connection up (i.e. dial the other end) when there are network
packets which must be transferred over the link. Once a dial-on-demand
connection is up, network traffic passing across the link causes the inactivity
timer for the link to be reset, keeping the connection up.
The RIP protocol periodically sends out update information across a link.
These periodic update packets will cause a WAN interface set for
dial-on-demand operation to stay up indefinitely.
These periodic update packets will cause a WAN interface set for
dial-on-demand operation to stay up indefinitely.