Lucent Technologies 6000 Manuale Utente
9-34
MAX 6000/3000 Network Configuration Guide
Configuring IP Routing
Configuring WAN interfaces
Configuring WAN interfaces
Settings in RADIUS profiles
The following attribute-value pairs configure IP options in a RADIUS profile:
Attribute
Value
Ascend-Route-IP (228)
Enables/disables IP routing for the interface. IP routing is enabled
by default.
by default.
Framed-Compression
(13)
(13)
Enables/disables Van Jacobsen prediction. You can specify Van-
Jacobson-TCP-IP to turn on TCP/IP header compression. If you do
not specify this value, RADIUS uses the default of no header
compression.
Jacobson-TCP-IP to turn on TCP/IP header compression. If you do
not specify this value, RADIUS uses the default of no header
compression.
Framed-IP-Address (8)
IP address of the calling device.
Framed-IP-Netmask (9)
Subnet mask of the caller’s address. If you do not specify a subnet
mask, the router assumes the default subnet mask based on address
class.
mask, the router assumes the default subnet mask based on address
class.
Ascend-PPP-Address
(253)
(253)
IP address assigned to the local side of a numbered-interface
connection.
connection.
Ascend-IF-Netmask
(153)
(153)
Subnet mask in use for the local side numbered interface.
Ascend-Metric (225)
RIP metric for the specified route (a number between 1 to 15,
default 7). If preference values are equal, the higher the metric, the
less likely that the MAX will use the route.
default 7). If preference values are equal, the higher the metric, the
less likely that the MAX will use the route.
Ascend-Route-Preference
(126)
(126)
A preference value for the route. Valid values are from 0 to 255. A
value of 255 prevents the use of the route.
value of 255 prevents the use of the route.
Framed-Route (22)
A static route definition, which can be used to make a user profile
a private route.
a private route.
Ascend-Assign-IP-Pool
(218)
(218)
Number of the address pool number from which to acquire an
address.
address.
Ascend-Assign-IP-
Global-Pool (146)
Global-Pool (146)
Name of a global address pool.
Ascend-IP-Direct (209)
IP address of a host to which all IP packets received across the link
will be directed.
will be directed.
Framed-Routing (10)
Enables/disables RIP updates on the interface. RIP is disabled by
default. Valid values are None(0), Broadcast(1), Listen(2),
Broadcast-Listen(3), Broadcast-v2(4), Listen-v2(5), and
Broadcast-Listen-v2(6).
default. Valid values are None(0), Broadcast(1), Listen(2),
Broadcast-Listen(3), Broadcast-v2(4), Listen-v2(5), and
Broadcast-Listen-v2(6).
Ascend-Source-IP-
Check (96)
Check (96)
Enables/disables anti-spoofing for the session. The default is
Source-IP-Check-No (0). If set to Source-IP-Check-Yes (1), the
system discards packets that do not originate on the subnet to
which the remote device is attached. The system determines the
subnet during IPCP negotiation. If Framed-IP-Netmask specifies a
subnet, packets that originate on that subnet are accepted. If
Framed-IP-Netmask specifies a 32-bit mask, only packets from a
single host are accepted. Packets sent from an address that does
not match are discarded.
Source-IP-Check-No (0). If set to Source-IP-Check-Yes (1), the
system discards packets that do not originate on the subnet to
which the remote device is attached. The system determines the
subnet during IPCP negotiation. If Framed-IP-Netmask specifies a
subnet, packets that originate on that subnet are accepted. If
Framed-IP-Netmask specifies a 32-bit mask, only packets from a
single host are accepted. Packets sent from an address that does
not match are discarded.
Ascend-Multicast-Client
(155)
(155)
Multicast forwarding option.