Toshiba TDP-T420 Manuale Utente
4
4
Operations
Using the menus (Continued)
Default setting 2 menu
Item
Description
Projection
mode
mode
Sets projection mode in accordance with Placement Style.
p.21
(Standard)
(Rear)
(Ceiling)
(Rear ceiling)
Fan mode
Sets the cooling fan speed.
Standard
High
Remote control When projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
[
[
or
: Enter setting] [
: Select from
1, 2
] [
: Confirm]
[
:Select
OK to end
]
Press [
Cancel] to return.
Key lock
Lock the control panel buttons.
[
[
or
: Enter setting] [
: Select
On/Off
] [
: Confirm]
[
:Select
OK to end
]
Press [
Cancel] to return.
Lamp power
Set the lamp power.
Low
Standard
Reset all
Press
. (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Yes
No
Password
Password setting
p.33
Press
. Password registration/Password setting
Detailed description
[Fan mode]
Setting [
Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).
meters above sea level).
Do not set Fan mode to [
High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from types. You can set each code respectively for up to
projectors. The factory setting is [
projectors. The factory setting is [
1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
A remote control code is applied after the setting is done.
You cannot operate the remote control if the codes of the projector and the remote
control do not match.
control do not match.
Remote control code setting for remote control
Set the same
remote control code switch as the projector.
p.16
p.17
•
•
[Key lock]
Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
with the control panel buttons is disabled.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
with the control panel buttons is disabled.
To release the key lock, set the [
Key lock] to [Off] using remote control. Pressing
the [
RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].
(When operating the main unit, the indicators of LAMP and TEMP light in orange
for seconds, and at the same time the projector beeps.).
for seconds, and at the same time the projector beeps.).
[Lamp power]
When [
Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Digital (DVI) Analog (D-SUB)(DVI)
Video S-video
RGB Y/P
B
/P
R
RGB Y/P
B
/P
R
Input
Input source name
Yes
Yes
Yes
Yes
Yes
Yes
Mode name
RGB input mode
[Note 1]
Yes
No
Yes
No
No
No
Resolution
Resolution (in dots)
Yes
No
Yes
No
No
No
Frequency
Sync frequency
Yes
No
Yes
No
No
No
Sync
Sync signal polarity
[Note ]
Yes
No
Yes
No
No
No
Signal format
Y/P
B
/P
R
signal format
No
Yes
No
Yes
No
No
Video mode
Color method of video signal
No
No
No
No
Yes
Yes
Lamp time
Time of lamp use
[Note ]
Yes
Yes
Yes
Yes
Yes
Yes
Lamp reset count
The count for lamp replacement Yes
Yes
Yes
Yes
Yes
Yes
Total time
The total time that this
projector is used.
projector is used.
Yes
Yes
Yes
Yes
Yes
Yes
Version
Firmware version
[Note 4]
Yes
Yes
Yes
Yes
Yes
Yes
Notes
1: The mode of supported RGB signals
p.53
is shown.
: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
: Displays [
: Displays [
Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches ,000
hours, consult with a dealer about getting replacement for:
hours, consult with a dealer about getting replacement for:
TLPLW40 (sold separately).
4: [
Version] shows the version of the projector’s internal control program. This version will
be requested for customer service purposes.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
information, dismiss the display, then display it again.
•
•