Toshiba TDP-D1 Manuale Utente

28

29

■ The image adjustment menu

Use this menu to adjust image-related items.
Items Items that can be adjusted are marked with  “Yes”, and those that cannot are marked
with “No”.

Item    

  

Description

Computer Y/P

B

/P

R

Video

S-video

 

Lower

Higher

Yes

Yes

Yes

Yes

Darker

Brighter

Yes

Yes

Yes

Yes

Lighter

Deeper

No

Yes

Yes

Yes

Reddish

Greenish

No

No

Yes

Yes

Softer

Sharper

No

Yes

Yes

Yes

Less red

More red

Yes

Yes

Yes

Yes

Less green

More green

Yes

Yes

Yes

Yes

Less blue

More blue

Yes

Yes

Yes

Yes

Shift down

Shift up

No

Yes

Yes

Yes

Notes
1: Tint can only be adjusted when Video mode 

 is NTSC or NTSC4.43.

2: Up/down shift can only be adjusted when Screen size 

 is Wide.  During the adjustment, the

picture may be instability.

■ The default setting menu

This menu shows placement status and other settings.

Set the time to wait after signal input stops until turning off the power: 
Off (not turned off)          1 min           2 min           ...          60 min

Set whether to turn on the power when the ON/STANDBY button is pressed 
(Manual), or the main power switch is used (Auto).          Manual             Auto

Set the lamp power                                    Standard           Low

Set standby mode according to functions used   Standard            Economy

Description

Item

(Back hung 
from ceiling)

(Placed 
on floor)

(Rear)

(Hung from 

ceiling)

Note
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets

quieter. This setting will be cleared when you turn the power off.

• Note that if Power on is set to Auto, then if the main power switch is turned on when

power is restored after a power outage, the projector power will come on.

• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.

Turning off the main power switch to cut off the power will shorten the life of the lamp.

■ The display setting menu

Use this menu to set screen display-related items.

(Full):  Display with native resolution (1,024 x 768 pixels)
(Thru): Display with sampling resolution (for computer input)
(Wide):  Wide-screen display (for Video, S-video, and Y/P

B

/P

R

)

Select one of the languages below to use for displaying menus and messages
[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/
Português/            /                      /                      /

Screen to display when there is no input signal                         (Logo)                            (Blue)                            (None)

Display icons as function guides

Display start-up screen when power turned on 

Description

Item

• If “Thru” is selected for screen size, portions exceeding the native resolution will not

appear on the screen. Note that for RGB signals with clock frequency 140MHz or lower,
all input pixel signals are sampled. (This effect is noticeable when the screen is enlarged
using the Resize function 

). However, if the clock speed is higher than this, the

RGB pixel signal is thinned before sampling.

■ Reset menu 

This menu is displayed when other menus are not displayed, and the 

 button is held

down until the menu appears.

• When the screen is placed vertically, and Auto keystone correction is executed, but

the keystone correction is not successful, stow the foot adjuster in its original position,
place the projector on a flat surface, select Horizontal reference value reset, and press
the 

 button.

• Select Reset All and press the 

 button to return all menu items to the factory settings.

Reset the horizontal reference value for Auto keystone correction
[     : Enter execution mode]     [Yes           No]     [Apply:     ]

Reset all menu items to their factory settings
[     : Enter execution mode]     [Yes           No]     [Apply:     ]

Description

Item