Land Pride 313-308M Manuale Utente
15
Section 3: Operating
4/03/08
PS2096 Series Primary Seeders 313-308M
Land Pride
Pull Tongue Hook-Up
1.
See “Pull Tongue Hook-Up” on page 13 for a
complete description of connecting a tractor to the pull
tongue and seeder.
complete description of connecting a tractor to the pull
tongue and seeder.
2.
At the field site, lower the seeder to the ground by
raising the transport wheels until the seeder is resting
on the ground. Transport wheels must also be resting
on the ground to support some of the seeder’s weight.
raising the transport wheels until the seeder is resting
on the ground. Transport wheels must also be resting
on the ground to support some of the seeder’s weight.
3.
Set the tractor’s hydraulic lever to return the lift
cylinder to this position each time the seeder is raised
and lowered.
cylinder to this position each time the seeder is raised
and lowered.
4.
With the seeder and transport wheels resting on level
ground, readjust the pull tongue top center link to level
the seeder if needed.
ground, readjust the pull tongue top center link to level
the seeder if needed.
5.
Remove rear roller lock pin from parking position and
place in storage position. Refer to Figure 2-1
place in storage position. Refer to Figure 2-1
Rear Roller Pin in Storage Position
Figure 2-1
!
CAUTION
Never back up with the seeder down. This will loosen the drive
chain and possibly damage the seeder.
chain and possibly damage the seeder.
Seeding
Slowly lower the Primary Seeder to the ground with the
tractor’s hydraulics. Begin in a low gear as the full seeder
can be a heavy load. Ground speed is determined based
on safety, ground conditions and terrain. In most cases do
not exceed 6 MPH. The seeding mechanism is ground
driven. Therefore, seeding can be discontinued by raising
the seeder off the ground with the 3-point lever before
making a turnaround and when transporting from one
area to another.
tractor’s hydraulics. Begin in a low gear as the full seeder
can be a heavy load. Ground speed is determined based
on safety, ground conditions and terrain. In most cases do
not exceed 6 MPH. The seeding mechanism is ground
driven. Therefore, seeding can be discontinued by raising
the seeder off the ground with the 3-point lever before
making a turnaround and when transporting from one
area to another.
IMPORTANT: Always operate the seeder with the
transport wheels on the ground and the seeder level
to prevent dirt build-up and damage to the seeder.
transport wheels on the ground and the seeder level
to prevent dirt build-up and damage to the seeder.
20578
Transporting
!
CAUTION
When traveling on public roads whether at night or during the
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
1.
Select a safe ground travel speed when transporting
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
2.
Reduce tractor ground speed when turning. Leave
enough clearance so the seeder does not contact
obstacles such as buildings, trees or fences.
enough clearance so the seeder does not contact
obstacles such as buildings, trees or fences.
3.
When traveling over rough or hilly terrain, shift tractor
to a lower gear.
to a lower gear.
Parking
The following steps should be done when preparing to
store the seeder or unhitch it from the tractor. See also
“Section 5: Maintenance & Lubrication” on Page 25 for
additional information on long term storage of your seeder.
store the seeder or unhitch it from the tractor. See also
“Section 5: Maintenance & Lubrication” on Page 25 for
additional information on long term storage of your seeder.
1.
Park the seeder on a level, solid area.
2.
Shut off tractor engine and engage parking brake.
3.
To prevent the seeder from tipping backward, remove
rear roller lock pin from storage position and place in
parking position. Refer to Figure 2-2
rear roller lock pin from storage position and place in
parking position. Refer to Figure 2-2
4.
Unhitch from tractor.
.
Rear Roller Pin in Parking Position
Figure 2-2
20579