Extron electronic PS 1230 Dépliant
1
PS 1230 External Power Supply •
Installation Guide
Installation Guide
About the PS 1230 Power Supply
Model
Part
Number
Power Output
Termination
PS 1230
70-769-01
36 watts, 12 VDC,
8 A peak, 3 A continuous; shared
between all three outputs
Captive screw
ZipClip
™
200 101-001-01
—
—
Connector Wiring
Ridged
Smooth
Tie
Wrap
3/16"
(5 mm) Max.
Captive Screw
Connector
Power Supply
Output Cord
Sleeve (-)
Tip (+)
Captive Screw Connector
Captive Screw Connector
Captive Screw Connector
DC Power Plug
Smooth
Ridged
Features
Power
LED
ZipClip
Mounting Slot
(front and rear)
Notches for
Securing
Tie Wrap
AC
Power
Input
DC Power
Outputs
Using the ZipClip 200
Attaching and Removing the Clip and Power Supply
To
attach the power supply to the ZipClip 200 mounting clip:
1.
Insert the bottom of the power supply down into the clip, starting with one
end.
end.
2.
Pivot the other end down and press until the clip snaps into place.
To
remove the power supply from the ZipClip:
1.
Press the tab on the ZipClip.
2.
Pivot the power supply and lift it out of
the ZipClip.
the ZipClip.
b
a
Rack Mounting
Mounting to a Rack Shelf
These power supplies are one quarter rack wide. Up to four power supplies can
be mounted side by side directly onto a rack shelf.
be mounted side by side directly onto a rack shelf.
1.
Align the threaded holes in the bottom of the power supply with the holes in
an Extron rack shelf and fasten the supply to the shelf with two screws as
shown below.
an Extron rack shelf and fasten the supply to the shelf with two screws as
shown below.
b
a
(2) 4-40 x 3/16"
Screws
RSB 123
Rack Shelf
Rack Mounted
2.
Bolt the rack shelf to the rack.
Contents
Using Tie Wraps for Cable Strain Relief
1.
Attach the power supply to the ZipClip 200 mounting clip as described
previously.
previously.
2.
Fasten the power output cords to the ZipClip base.
a.
Insert tie wraps (which are also called “zip ties”) along the notches
on the side of the power supply and through the tie wrap anchor
points on the ZipClip, then around the cord.
on the side of the power supply and through the tie wrap anchor
points on the ZipClip, then around the cord.
b.
Connect and pull the tie wraps until they are secure. Do not over
tighten.
tighten.
Tie Wrap
Mounting to Rack Rails Using a ZipClip
1.
Fasten the ZipClip 200 mounting clip to a rack rail using two rack screws
(see the diagram below).
(see the diagram below).
2.
Insert the bottom of the power supply down into the clip, starting with one
end.
end.
3.
Pivot the other end toward the clip and press until the clip snaps into place.
Inside of Rack
ZipClip 200
Back of Rack
Side of Rack
Important Safety Instructions
This symbol is intended to alert the user of
important operating and maintenance (servicing)
instructions in the literature provided with the
equipment.
important operating and maintenance (servicing)
instructions in the literature provided with the
equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product enclosure that may present a risk of
electric shock. On the product, risk of shock may
be indicated by this symbol.
be indicated by this symbol.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from
the apparatus.
the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this device apparatus during lightning storms or when unused
Unplug this device apparatus during lightning storms or when unused
for long periods of time.
WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.”
“This apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases shall be placed
on the apparatus”
“This apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases shall be placed
on the apparatus”
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as when
the power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
the power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
WARNING: This apparatus is a Class I product. This product
must be connected to a MAINS socket outlet with a protective
earthing connection.
earthing connection.
The mains plug is used as the disconnect device and shall remain readily
operable.
To prevent the risk of shock, do not attempt to service this equipment
yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
dangerous voltage or other hazards.
WARNING:
Power sources • This equipment should be operated only from
Power sources • This equipment should be operated only from
the power source indicated on the product. This equipment
is intended to be used with a main power system with a
grounded (neutral) conductor. The third (grounding) pin is a
safety feature, do not attempt to bypass or disable it.
is intended to be used with a main power system with a
grounded (neutral) conductor. The third (grounding) pin is a
safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment
safely, remove all power cords from the rear of the equipment,
or the desktop power module (if detachable), or from the
power source receptacle (wall plug).
or the desktop power module (if detachable), or from the
power source receptacle (wall plug).
See the next page for furniture mounting instructions.
NOTES REGARDING REVISION C:
z
Added altitude and sea level text and
symbols for CCC compliance per Homi.
symbols for CCC compliance per Homi.
z
Added standard Extron logo document
header.
header.
z
Updated corporate contact info to include
India and Korea offices and updated
phone numbers throughout.
India and Korea offices and updated
phone numbers throughout.
z
Updated 5 illustrations
z
Replaced specifications with latest
version.
version.
z
Changed various fonts and styles to
current department style.
current department style.
z
See this ER:
http://intranet/app/ER/ERGeneration/
logdetail.aspx?logid=11838 .
http://intranet/app/ER/ERGeneration/
logdetail.aspx?logid=11838 .
Base level part number:
28-113-07LF.
28-113-07LF.