Behringer Power Mixer Manuale Utente

EUROPOWER PMH2000

2. CONTROL ELEMENTS

The stereo equalizer is effective on the main mix when

both units have been activated with the EQ IN buttons

and the MODE switch

is set to its upper position

(LEFT/RIGHT).

The stereo equalizer uses one unit each to process the

main and monitor mix signals, if both units are on and the

MODE switch

is set to its lower position (MON/MAIN).

Use the EQ IN buttons to switch the two equalizer units on

or off.
Press the RUMBLE FILTER button to activate the low-cut

filter of channels 1 - 6. This filter eliminates unpleasant

bass frequencies (e.g. microphone pop noise).
The FX TO MON control determines the effects intensity

of the multi-effects processor as part of the monitor mix.

Turn the control fully counter-clockwise to add no effect to

the monitor mix.
The MONITOR LEVEL control adjusts the volume of the

monitor mix.
Use the MONITOR LEVEL display to control the monitor

signal level. The upper LED (LIM) lights up when the built-in

limiter is activated, thus protecting against overload.
With this MODE switch you can determine whether the

PMH2000 works as a stereo amplifier (LEFT/RIGHT) or

as a dual mono amplifier (MON/MAIN). Please note that

the equalizer function also depends on this switch setting

(see

The FX TO MAIN control functions as FX return for the

built-in effects processor. Use this control to add the

desired effect signal to the main mix. No effect signal is

added when the FX TO MAIN is set fully counter-clockwise.
The MAIN LEVEL control governs the overall volume of the

PMH2000.
The MAIN LEVEL display reads the output level of the

PMH2000. The upper LED (LIM) lights up when the built-in

limiter is activated, thus protecting against signal peaks.
Use the FX FOOTSWITCH jack to connect any commercially

available foot controller. It allows you to bypass the effects

unit.
This is the balanced MONITOR output of your PMH2000.

Use it to feed an external monitor amp or active wedge.
These two 1/4" TS jacks allow you to route the output

signal to an external amplifier. This allows you to, say, use

only the mixing and effect section of the PMH2000. The

signal is taken pre-power amp. Of course, you can also

use only the left jack as a mono output.
These two 1/4" TS jacks can be used to connect external

signals, such as the main mix signal from an additional

mixing console (pre-power amp).
Here, you will find a list of all multi-effect presets available.
This is the LED level meter of the effects processor. Please

make sure that the clip LED lights up with signal peaks only.

If it is lit constantly, this indicates that the effects processor

is overdriven, which can lead to unpleasant distortion.
The EFFECT display reads the currently selected preset.
Turn the PROGRAM control to select the effect presets.

Press the control briefly to confirm your selection.

2.2 Rear panel

The mains connection is on a standard IEC receptacle. An

appropriate power cord is supplied with the unit.
FUSE HOLDER. Before connecting the unit to the mains,

ensure that the voltage setting matches your local voltage.

Blown fuses should only be replaced by fuses of the same

type and rating.
Use the POWER switch to put your PMH2000 into operation.

The POWER switch should always be in the Off position

when you are about to connect your unit to the mains.

Attention: The POWER switch does not fully

disconnect the unit from the mains. Unplug the

power cord completely when the unit is not used

for prolonged periods of time.
This is the RIGHT/MONO MAIN Speakon

loudspeaker

output of your PMH2000, where you can connect the right

loudspeaker of a stereo system. For this purpose, switch

must be set to its upper position. If, however, you run

a mono main mix (switch

set to its lower position), this

loudspeaker output provides the main mix signal in mono.

The impedance of the loudspeaker connected here

must not fall below 4

The BRIDGE loudspeaker output allows you to combine

the left and right stereo channel in one mono output, which

is useful for applications that require the use of one

loudspeaker only. To use the BRIDGE output, switch

must be set to LEFT/RIGHT.

Always connect the BRIDGE jack to a loudspeaker

with a minimum impedance of 8

Please note that the power delivered to the speaker

connected to the BRIDGE output is considerably

higher than the power provided to the speakers

wired to the parallel speaker outputs. Please read

the information given on the rear panel of your

PMH2000.

When using the BRIDGE loudspeaker output, NEVER

use any of the other two connectors (RIGHT/MONO

MAIN and LEFT/MONITOR) at the same time!
This is the LEFT/MONITOR Speakon

loudspeaker output

of your PMH2000, to which you can connect the left

loudspeaker of a stereo system (switch

set to its

upper position). If you do a main mix in mono (switch

set to its lower position), this loudspeaker output provides

the monitor signal in mono.

The impedance of the loudspeaker connected here

must not fall below 4

Information on how to properly connect your

speaker with regard to polarity can be found on the

rear of the unit (PIN assignment).
SERIAL NUMBER. Please take the time to fill in and return

the warranty card within 14 days after the date of purchase,

so as to benefit from our extended warranty. Or register

online at www.behringer.com.

3. EFFECTS PROCESSOR

A special feature of your PMH2000 is its built-in multi-effects

processor that features the same audio quality as our re-

nowned 19" effects device VIRTUALIZER PRO DSP2024P. The

processor comes with 99 different standard effects such as

reverb, chorus, flanger, delay, vocal distortion as well as various

effects combinations.