Black Box LES1216A-R2 Manuale Utente
Specify the Probe Addresses of two sites (the Primary and Secondary) that the console server
is to ping to determine if the principal network is still operational
is to ping to determine if the principal network is still operational
In event of a failure of the principal network the 3G network connection is activated as the access
path to the console server (and its Managed Devices). Only HTTPS and SSH access is enabled
on the failover connection (which should enable the administrator to connect and fix the problem)
path to the console server (and its Managed Devices). Only HTTPS and SSH access is enabled
on the failover connection (which should enable the administrator to connect and fix the problem)
Note: By default, the console server supports automatic failure-recovery back to the original state prior
to failover .The console server continually pings probe addresses whilst in original and failover
states. The original state will automatically be set as a priority and reestablished following three
successful pings of the probe addresses during failover. The failover state will be removed once
the original state has been re-established.
states. The original state will automatically be set as a priority and reestablished following three
successful pings of the probe addresses during failover. The failover state will be removed once
the original state has been re-established.
For earlier firmware that does not support automatic failure-recovery, to restore networking to a
recovered state the following command then needs to be run:
recovered state the following command then needs to be run:
rm -f /var/run/*-failed-over && config -r ipconfig
If required, you can run a custom bash script when the device fails over. It is possible to use this
script to implement automatic failure recovery, depending on your network setup. The script to
create is:
script to implement automatic failure recovery, depending on your network setup. The script to
create is:
/etc/config/scripts/interface-failover-alert
You can check the connection status by selecting the Cellular panel on the Status: Statistics
menu
o
The Operational Status will change as the cellular modem finds a channel and connects to
the network
o
The Failover & Out-of-Band screen will display information relating to a configured
Failover/OOB interface and the status of that connection. The IP Address of the Failover/
OOB interface will be presented in the Failover & Out-of-Band screen once the
Failover/OOB interface has been triggered
OOB interface will be presented in the Failover & Out-of-Band screen once the
Failover/OOB interface has been triggered
5.7.3
Cellular routing
Once you have configured carrier connection, the cellular modem can be configured to route traffic
through the console server. This requires setting up forwarding and masquerading - as detailed in
Chapter 5.8.
through the console server. This requires setting up forwarding and masquerading - as detailed in
Chapter 5.8.
5.7.4
Cellular CSD dial-in setup
Once you have configured carrier connection, the cellular modem can be configured to receive Circuit
Switched Data (CSD) calls.
Switched Data (CSD) calls.
Note: CSD is a legacy form of data transmission developed for the TDMA based mobile phone systems
like GSM. CSD uses a single radio time slot to deliver 9.6kb/s data transmission to the
GSM Network and Switching Subsystem where it could be connected through the equivalent of a
normal modem to the Public Switched Telephone Network (PSTN) allowing direct calls to
any dial-up service. CSD is provided selectively by carriers and it is important you receive a Data
Terminating number as part of the mobile service your carrier provides. This is the number which
external modems will call to access the console server
GSM Network and Switching Subsystem where it could be connected through the equivalent of a
normal modem to the Public Switched Telephone Network (PSTN) allowing direct calls to
any dial-up service. CSD is provided selectively by carriers and it is important you receive a Data
Terminating number as part of the mobile service your carrier provides. This is the number which
external modems will call to access the console server
Select the Cellular Modem panel on the System: Dial menu
Check Enable Dial-In and configure the Dial-In Settings
_____________________________________________________________________
724-746-5500 | blackbox.com
Page 94