Panasonic CF-F8 Manuale Utente

25

Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the 

“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact 
your technical support office. You can also check the computer’s status in the PC Information Viewer (Î

 Reference 

Manual “Check the Computer’s Usage Status”).

„

The computer does not 
power on/
The power indicator or bat-
tery indicator is not lit.

z

Connect the AC adaptor.

z

Insert a fully charged battery.

z

Remove the battery pack and the AC adaptor, then connect them again. 

z

If an additional RAM module has been inserted, remove the RAM module and check to 

see if the RAM module is the recommended one.

z

When the CPU temperature is high, the computer may not start up to prevent overheating of 

the CPU. Wait until the computer cools down, and then turn the power on again. If the com-

puter does not power on even after cooling down, contact your technical support office.

Windows does not start up.

z

Remove all peripheral devices (e.g. USB memory).

z

If an additional RAM module has been inserted, remove the RAM module and check to 

see if the RAM module is the recommended one.

z

If the power indicator is lit, slide the power switch for four seconds or longer to turn off, 

then turn on again.

z

Using the following procedure, start up in Safe Mode, and check the error details.

A

Turn on the computer, and when the [Panasonic] boot screen disappears (after enter-
ing the password

*1

 if one is set) hold down 

F8

.

B

Release your finger when [Windows Advanced Options Menu] is displayed, and with 
Ï

 or Ð, select [Safe Mode], then press 

Enter

.

Follow the on-screen instructions.

*1

Supervisor Password or User Password set with the Setup Utility

z

Press 

F9

 in the Setup Utility (Πpage 28 “To start the Setup Utility”) to return the Setup 

Utility settings (excluding the passwords) to the default values. Start the Setup Utility and 
make the settings again.

Cannot boot from internal 
CD/DVD drive.

z

Make sure that the bootable CD/DVD is set properly.

z

Start the Setup Utility, and confirm the following settings.

• [Optical Drive] is set to [Enabled] in the [Advanced] menu.

• [Optical Drive Power] is set to [On] in the [Main] menu.

• [Boot Option #1] is set to [CD/DVD Drive] in the [Boot] menu.

z

When an external CD/DVD drive is connected, you cannot boot from the internal CD/

DVD drive.

You have forgotten the 
password.

z

Supervisor Password or User Password: Contact 

your technical support office

.

z

Administrator password: 

• If you have a password reset disk, you can reset the administrator password. Set the 

disk and enter any wrong password, then follow the on-screen instructions and set a 

new password.

• If you do not have a password reset disk, reinstall (ΠSupplementary Instructions for 

Windows XP) and set up Windows, and then set a new password.

“Remove disks or other 
media. Press any key to 
restart” or a similar mes-
sage appears.

z

A floppy disk is in the floppy disk drive and it does not contain system startup informa-

tion. Remove the floppy disk and press any key.

z

This message may appear with some devices connected to 

the USB port

. Remove the 

device or set [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.

z

If the problem persists after removing the disk, it may be a hard disk failure. Perform the rein-

stallation and return the hard disk to its condition at the time of purchase. (ΠSupplementary 

Instructions for Windows XP) If the problem persists even after the reinstallation, contact 

your technical support office

.

[Executing Battery Recali-

bration] screen appears.

z

The Battery Recalibration was canceled before Windows was shut down last time. To 
start up Windows, turn off the computer by the power switch, and then turn on.

The computer will not auto-
matically enter standby/
hibernation.

z

If you connect to a network using wireless LAN function, perform access point settings. 
(Î

 

Reference Manual “Wireless LAN”)

z

If you do not use wireless LAN function, turn off wireless LAN function. (Î

 

ence Manual “Disabling/Enabling Wireless Communication”)

z

Make sure that you are not using any software that regularly accesses the hard disk.

When logging on (e.g., 
resuming the computer), 
audio is distorted.

z

Perform

 the following steps to change the audio settings to prevent audio output.

A

Click [start] - [Control Panel] - [Sounds, Speech, and Audio Devices] - [Sounds and 

Audio Devices], and click [Sounds].

B

Set [Windows Logon] and [Windows Logoff] to [(None)].