Spectra HL700 Dépliant

A) HL700 is in the laser beam and the 

power is on:

Press any switch to return to normal 

operation.

The current elevation read-

ing will be held. A flashing 

display will confirm the 

reading has been captured

.

1 x quick

B) HL700 is out of the laser beam and 

power is on:

A short intermittent 

beep (The beeper 

will turn on to Low if 

turned off.)

+

1.

Press any switch to return to normal 

operation.

2. Place the HL700 in the beam. (Example: 

HL700 into the laser beam. You now have 

The beeper will 

chirp rapidly after 

approximately 5 

seconds to confirm 

beam capture. A flashing 

display will also indicate 

the reading has been 

captured

.

+

1 x quick

SENS

 

Sensitivity Medium*-HighLow

AVG

 

Averaging algorithm Medium*High - Low

D.R.O

.  Numeric display ON*-OFF-.1mm

UNIT

 

Units of measure MM*-CM-IN-FRAC-FT

FRC.R

.  Fractional Reduction ON*-OFF

ARRW

  Arrow Display DB*(deadband)-PR (prop.)

O.O.B.

  Out-of-Beam Display ON*-OFF

GRD.A

.  Grade Alarm ON-OFF*

A.S.O

.  Automatic shutoff 0.5h*-24h-OFF

TX.O.L

.  Transmitter Out-of-Level OFF*RPS

TX.O.B

.  Transmitter Low Battery OFF*-RPS

INFO

 

Information about the Laserometer

(for 2 Sec., then SENS)

Press switches  

together for 2 sec

.

1. Scrolling up or down.

 

How to change Menu functions:

2. Enter Change mode.

3. Change selected items

.

4. Confirm change

.

5. To Exit.

or

+

A.S.O. (Automatic Shut Off): 

0.5 - After 30 Minutes*

OF - Off (Unit is permanently on.)

24 - 24 hour shutoff.

Out-of-Beam Display 

O.O.B. (Out-of-Beam Display): 

Sequence to show direction to get back in 

the laser beam ( for 25 s)

ON - Out-of-Beam Display ON* 

OF - Out-of-Beam Display OFF

Grade Alarm 

GRD.A. (Grade Alarm): 

When turned ON, disables the audible 

signal when on-grade. When moved out 

of the on-grade deadband, the beeper 

activates as normal:

ON - Alarm on (Solid beeper OFF)

OF - Alarm off (Solid beeper ON)*

* Default setting

SENS (Sensitivity): 

Selects reception sensitivity to laser and 

other light sources.

MD - Medium*: for most applications.

HI -   High: When laser beam is 

 

weak, or at very long distances.

LO -  Low: If outside sources are 

 

disturbing elevation readings

.

Initialization:

1. Test of LCD, LED and beeper

2. CAL: Calibration (3 sec.)

3. Unit is ready for use.

(Do not power up the unit in a laser beam 

or strobe. If detected, the unit will display 

“E200” and revert to the previous

calibration.)

The selected unit of measure determines 

the displayed deadband (accuracy).

The current accuracy is stored in memory 

and will be retained when the unit is turned 

off or when batteries are replaced.

The current beeper 

volume is stored in 

memory and will be 

retained when the unit is 

turned off or when bat-

teries are replaced.

The current unit of measure is stored in 

memory and will be retained when the unit 

is turned off or when batteries are replaced.

The current brightness of LEDs 

is stored in memory and will 

be retained when the unit is 

turned off or when batteries are 

replaced.

Accuracy in mm:
0.5   1.0    2.0   5.0  10.0

Beeper 

Loud

Beeper 

Medium

Beeper 

Low

(No symbol)

mm - cm - in - frac - ft

 

LEDs 

Bright

LEDs  

Dim

LEDs 

OFF

(No symbol)

1

2

3

Press and hold for 2 seconds to turn 

power OFF.

Press once to display current setting;

push again to scroll through options.

Press together to cycle the selection

.

+

Press once to display current setting, 

additional pushes to scroll through options.

Press once to change current setting

(A beep confirms the selected volume.)

Beeper 

Off