RedMax BM461 Manuale Utente
8
Before you remove cap, be sure there is no pressure in
the tank. in order to release pressure, invert unit upside
down and squeeze spray pistol (aim away from you).
Pressure will escape; when hissing stops, all pressure
has been released. Remove pump assembly by turning
counter-clockwise. The pump handle has two locking
positions, one turning clockwise and one counter-
clockwise.
the tank. in order to release pressure, invert unit upside
down and squeeze spray pistol (aim away from you).
Pressure will escape; when hissing stops, all pressure
has been released. Remove pump assembly by turning
counter-clockwise. The pump handle has two locking
positions, one turning clockwise and one counter-
clockwise.
1. Remove cap and pour out remaining solution, then rinse all
parts thoroughly with clean water.
2. Add 1/2 gallon of fresh water in tank. Pressurize, and flush
pumping system by depressing trigger for at least two
minutes; then drain all remaining water.
minutes; then drain all remaining water.
• Periodically re-grease lid gasket as well as lid vent and
pump cylinder, where applicable.
• To ensure good performance, keep lid vent free of
obstruction. Before and after each use, make sure all
connections are well tightened. Service and replace worn
parts as required.
connections are well tightened. Service and replace worn
parts as required.
Failure to follow manufacturer's recommendation of use and
care of unit will void any expressed or implied warranty. Do
not use chlorine or clorox. It will permanently damage pump
system.
care of unit will void any expressed or implied warranty. Do
not use chlorine or clorox. It will permanently damage pump
system.
In the event that any part must be replaced or any
maintenance or repair work not described in this manual must
be performed, please contact a representative from the store
nearest RedMax authorized servicing dealer for assistance.
maintenance or repair work not described in this manual must
be performed, please contact a representative from the store
nearest RedMax authorized servicing dealer for assistance.
NOTE
NOTE
WARNING
8. Maintenance
■ SPRYAER MAINTENANCE TABLE
Dayly
System/Compornent
Procedure
or
Before Use
After Use
Lid Gasket
Grease
✓
Lid Vent
Inspect/Clean
✓
Pump
Grease
✓
Connection
Inspect/Tight
✓
Whole unit
Wash/inspect
✓
7. Operation
• Always release pressure in the pump prior to filling,
cleaning, or servicing the sprayer.
• Before opening a container of pesticide or other spray
material, carefully read, understand, and follow all
instructions on the label.
instructions on the label.
• Do not use flammable materials in the sprayer: they can
ignite and/or explode, causing serious injury.
• Never use caustic or corrosive materials in the sprayer,
which could result in damage to the unit.
■ HOW TO ADJUST THE NOZZLE
• To adjust nozzle, tighten cap (turn clockwise) for fine
atomized spray, or loosen (turn counter-clockwise) for
coarser spray or solid stream.
coarser spray or solid stream.
■ HOW TO PREPARE YOUR UNIT FOR USE
• Normal working pressure should be from 25 psi to 40 psi.
Too much pressure will waist chemical and over apply, as
well as causing potential damage to pump tube.
well as causing potential damage to pump tube.
• Pump occasionally to maintain the desired spraying
pressure.
■ RECOMMENDED APPLICATIONS FOR
"LAWN AND GARDEN" OR "AGRICULTURE" USAGE.
"LAWN AND GARDEN" OR "AGRICULTURE" USAGE.
Herbicide : Yes
Insecticides/Pesticides : Yes
Fertilizers : Yes
Chlorine based : Yes
Diesel : Yes
Wettable Powder : Yes
Stains & Sealers : Yes
Oil Based : Yes
Solvent-Based : Yes
Viscous : No
Insecticides/Pesticides : Yes
Fertilizers : Yes
Chlorine based : Yes
Diesel : Yes
Wettable Powder : Yes
Stains & Sealers : Yes
Oil Based : Yes
Solvent-Based : Yes
Viscous : No