Bostitch N401C Manuale Utente

-10-

O-ring cut or cracked  . . . . . . . . . . . . . . . . . . . .Replace O-ring

O-ring/seals cut or cracked . . . . . . . . . . . . . . . .Replace trigger valve assembly

Loose nose screws . . . . . . . . . . . . . . . . . . . . . .Tighten and recheck

O-ring or Gasket is cut or cracked  . . . . . . . . . .Replace O-ring or gasket

Bumper cracked/worn . . . . . . . . . . . . . . . . . . . .Replace bumper

Damaged gasket or seal . . . . . . . . . . . . . . . . . .Replace gasket or seal

Cracked/worn head valve bumper . . . . . . . . . . .Replace bumper

Loose cap screws  . . . . . . . . . . . . . . . . . . . . . .Tighten and recheck

Air supply restriction  . . . . . . . . . . . . . . . . . . . . .Check air supply equipment

Tool dry, lack of lubrication  . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant

Worn head valve O-rings  . . . . . . . . . . . . . . . . .Replace O-rings

Broken cylinder cap spring  . . . . . . . . . . . . . . . .Replace cylinder cap spring

Head valve stuck in cap  . . . . . . . . . . . . . . . . . .Disassemble/Check/Lubricate

Tool dry, lacks lubrication  . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant

Broken cylinder cap spring  . . . . . . . . . . . . . . . .Replace cap spring

O-rings/seals cut or cracked  . . . . . . . . . . . . . . .Replace O-rings/seals

Exhaust blocked   . . . . . . . . . . . . . . . . . . . . . . .Check bumper, head valve spring, muffler

Trigger assembly worn/leaks  . . . . . . . . . . . . . .Replace trigger assembly

Dirt/tar build up on driver  . . . . . . . . . . . . . . . . .Disassemble nose/driver to clean

Cylinder sleeve not seated correctly
on bottom bumper  . . . . . . . . . . . . . . . . . . . . . .Disassemble to correct

Head valve dry  . . . . . . . . . . . . . . . . . . . . . . . . .Disassemble/lubricate
Air pressure too low  . . . . . . . . . . . . . . . . . . . . .Check air supply equipment

Skipping fasteners;  intermittent feed Worn bumper  . . . . . . . . . . . . . . . . . . . . . . . . . .Replace bumper

Tar/dirt in driver channel  . . . . . . . . . . . . . . . . . .Disassemble and clean nose and driver

Air restriction/inadequate air flow through
quick disconnect socket and plug  . . . . . . . . . . .Replace quick disconnect fittings

Worn piston O-ring  . . . . . . . . . . . . . . . . . . . . . .Replace O-ring, check driver
Tool dry, lacks lubrication  . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant

Damaged feed piston spring . . . . . . . . . . . . . . .Replace spring

Low air pressure . . . . . . . . . . . . . . . . . . . . . . . .Check air supply system to tool

Loose canister nose screws  . . . . . . . . . . . . . . .Tighten all screws

Fasteners too short for tool . . . . . . . . . . . . . . . .Use only recommended fasteners

Bent fasteners  . . . . . . . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners

Wrong size fasteners  . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners

Leaking head cap gasket  . . . . . . . . . . . . . . . . .Tighten screws/replace gasket

Trigger valve O-ring cut/worn  . . . . . . . . . . . . . .Replace O-ring

Broken/chipped driver . . . . . . . . . . . . . . . . . . . .Replace driver (check piston O-ring)

Dry/dirty magazine  . . . . . . . . . . . . . . . . . . . . . .Clean/lubricate use BOSTITCH Air Tool Lubricant

Driver channel worn  . . . . . . . . . . . . . . . . . . . . .Replace nose/check door

Wrong size fasteners  . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners

Bent fasteners  . . . . . . . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners

Loose canister/nose screws  . . . . . . . . . . . . . . .Tighten all screws

Broken/chipped driver . . . . . . . . . . . . . . . . . . . .Replace driver

Feed piston dry  . . . . . . . . . . . . . . . . . . . . . . . .Add BOSTITCH Air Tool Lubricant  in hole in feed piston cover

Feed piston O-rings cracked/worn  . . . . . . . . . .Replace O-rings/check bumper and spring. Lubricate assembly.

Check Pawl binding  . . . . . . . . . . . . . . . . . . . . .Inspect Pawl and spring on door. Must work freely.

Canister bottom not set correctly  . . . . . . . . . . .Set canister bottom for length of nails being used

Broken weld wires in nail coil  . . . . . . . . . . . . . .Remove coil of nails and use another coil

Wrong size fasteners for tool  . . . . . . . . . . . . . .Use only recommended fasteners/check canister bottom adjustment

Broken welded wires in nail coil  . . . . . . . . . . . .Remove coil of nails and use another coil

Wrong slide plate adjustment for
wire collated nail coil  . . . . . . . . . . . . . . . . . . . .Adjust switch pins for wire collated nail coil

-11-