Roland VC-2 Manuale Utente

Pagina di 72
 
25
 
Creating/Editing Patches (Patch mode)
4.
 
When you have finished inputting, touch <OK> 
to finalize the mic setting name.
 
There are three pre-effects: compressor, limiter, and noise 
suppressor. By using these you can adjust the level of the 
sound being sampled.
 
Noise suppressor:
 
 This effect leaves the original sound 
untouched, but mutes the noise that is heard during periods of 
silence.
 
Compressor:
 
 By reducing high levels and raising low levels, 
this effect smoothes out unevenness in volume.
 
Limiter:
 
 By compressing sounds that exceed a specified 
volume level, this effect prevents the sound from distorting.
 
OFF
 
No pre-effect will be used.
 
EQ LOW/MID/HIGH (Three-band equalizer)
 
NS-COMP
 
Compressor and noise suppressor settings can be made.
 
For the parameters of the three-band equalizer, refer to 
the explanation of 
 
OFF
 
.
 
NOISE SUPRESSOR
COMPRESSOR
 
NS-LIMIT
 
Limiter and noise suppressor settings can be made.
 
For the parameters of the three-band equalizer, refer to 
the explanation of 
 
OFF
 
.
 
PRE-EFX Type (Pre-Effect Types)
 
Parameter
Value
Explanation
 
EQ 
LOW
Freq
50, 63, 80, 100, 125, 160, 
200, 250, 315, 400, 500, 
630, 800, 1000, 1250, 
1600, 2000, 2500, 3150, 
4000 Hz
Selects the frequency 
of the low range.
Gain
-15– +15 dB
Adjusts the gain of 
the low frequency. 
Positive (+) settings 
will emphasize the 
low-frequency 
range.
EQ 
MID
Freq
50, 63, 80, 100, 125, 160, 
200, 250, 315, 400, 500, 
630, 800, 1000, 1250, 
1600, 2000, 2500, 3150, 
4000, 5000, 6300, 8000, 
10000, 12500, 16000, 
20000 Hz
Selects the frequency 
of the middle range.
Q
0.3, 0.4, 0.6, 0.8, 1.0, 1.5, 
2.0, 2.5. 3.0, 3.5, 4.0, 5.0, 
6.0, 7.0, 8.0, 10.0, 12.0, 
14.0, 16.0, 18.0, 20.0
Adjusts the width of 
the middle range. Set 
a higher value for Q 
to narrow the range 
to be affected.
Gain
-15– +15 dB
Adjusts the gain of 
the middle range. 
Positive (+) settings 
will emphasize the 
middle range.
EQ 
HIGH
Freq
2000, 4000, 5000, 6300, 
8000, 10000, 12500, 
16000, 20000 Hz
Selects the frequency 
of the high range.
Gain
-15– +15 dB
Adjusts the gain of 
the high frequency. 
Positive (+) settings 
will emphasize the 
high-frequency 
range.
MIC LEVEL
0–127
Adjusts the volume 
of the mic.
 
* This is linked with 
MIC Level in the 
top screen.
 
Parameter
Value
Explanation
 
Thres 
(Threshold 
Level)
-60–0 dB
Specifies the level at which the noise 
suppressor will begin to operate. When 
the signal falls below the specified lev-
el, it will be muted.
Release 
(Release 
Time)
0–127
Specifies the time from when the noise 
suppressor begins to operate until the 
volume reaches 0.
 
Parameter
Value
Explanation
 
Gain
0–127
Adjusts the output gain.
Attack (At-
tack Time)
0–127
Specifies the attack time of the input 
sound.
Release 
(Release 
Time)
0–127
Specifies the time from when the compres-
sor begins to operate until the volume 
reaches 0.
Level (Out-
put Level)
0–127
Adjusts the volume of the mic.
 
* This is linked with MIC Level in the top 
screen.
 
Parameter
Value
Explanation
vc2_for_XT_e1 25 ページ 2005年3月8日 火曜日 午後4時52分