Cooper Lighting IMI-6950 Manuale Utente

TASK LIGHT FIELD KIT INSTALLATION: (Figure 1)
1. Note: Remove tamper proof screws first if luminaire includes (TR) 

tamper-resistant option. (Figure 1).

2. To release clasp lock on “quick mount” bracket, push handle inward and

pull luminaire forward. (Figure 2). CAUTION: Do not let luminaire fall.  
Support luminaire while lowering off of j-box to resting/hanging position.

3. Remove luminaire hanging hook from quick mount plate (Figure 3 & 4).

CAUTION: Support luminaire while removing.
CAUTION: DO NOT place luminaire directly with lens facing down; it may 
scratch or cause the lens to break. Place fixture with lens facing upright on 
stable work surface. SUGGESTION: Remove the lens completely in order to 
perform remaining of Task Light accessory installation. 
Unlatch both latches. CAUTION: To avoid lens breakage, remove lens 
retainer if necessary (Figure 5). Remove the complete lens assembly and 
set aside to prevent damage. Take off upper reflector by loosening 
thumbscrews (See figure 6).  

4. Reference dimensions as shown and mark housing if necessary 

(Figure 7 & 8).

5. Line up an adapter block and secure tightly if possible to aid in drilling 

(Figure 7 & 8).
CAUTION: DO NOT drill or damage other components inside luminaire. To 
avoid this from happening, remove them if necessary.

6. Drill center hole as specified and de-burr if necessary to remove sharp

edges (Figure 7 & 8). 

7. Drill and tap the two outside holes as specified (Figure 7 & 8). 
8. Install gasket and adapter block (with provided fasteners) (Figure 9). 
9. Apply sealing compound on the threads of handle (provided by others).
10.  Pull wires out of head through access in block. Screw the handle into 

adapter block. On inside of fixture, make connections and restrain with 
wire tie.

11.  Aim the handle to a preferred position and lock it in position.
12. Aim task light head to a preferred position and tighten #10-24 Allen head 

screw (with provided Allen wrench).

13.  To install lamp, remove task light cover by twisting counter-clockwise and 

pulling out (Figure 9). CAUTION: Verify that lamp source and wattage 
correspond with the luminaire label.

14.  Re-install task light cover by pushing in and rotating clockwise (Figure 9).

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative. 
NOTE: Specifications and dimensions subject to change without notice.

GENERAL: Upon receipt of luminaire thoroughly inspect for any freight
damage, which should be brought to the attention of the delivery 
carrier. Compare the catalog description listed on the packing slip 
with the luminaire label on the housing to assure you have received the 
correct merchandise.
SAFETY: This luminaire must be wired in accordance with the national
electrical code and applicable codes and ordinance. Proper grounding 
is required to insure personal safety. Carefully observe grounding 
procedure. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF before starting installation or
attempting any maintenance.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit
breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow luminaire to cool
before changing lamp or handling luminaire.
WARNING: RISK OF FIRE! DO NOT mount on or near combustible 
materials.

Customer First Center  1121 Highway 74 South  Peachtree City, GA  30269  770.486.4800  FAX  770.486.4801    ADH080775

TAMPER-PROOF
SCREW FOR HANDLE

TAMPER-PROOF
SCREW FOR LATCH

HANDLE

PUSH

PULL

LATCH

QUICK MOUNT
PLATE

HANGING
HOOK

LUMINAIRE