Chauvet 250 Manuale Utente
Q-Wash 250 User Manual
3
2006-05-17/13:18
100V
100V
115V
115V
208V
208V
230V
230V
240V
240V
50Hz
50Hz
60Hz
IN
IN
60Hz
Select volt age
T
o
B
a
lla
s
t 2
3
0
V
/5
0
H
z
T
o
B
a
lla
s
t 2
3
0
V
/6
0
H
z
L
a
m
p
C
o
n
tr
o
l t
o
P
C
B
in
AC-100-230V
INPUT
To TRANSFORME R
B
EFORE
Y
OU
B
EGIN
What is included
Q-Wash
™ 250
Power cord with plug
HSD-250 Discharge lamp
Manual
Warranty Card
230V Fuse
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture
’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be
powered directly off a switched circuit and cannot be run
off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0%
to 100% switch. Before applying power to a fixture,
check that the source voltage matches the fixture
powered directly off a switched circuit and cannot be run
off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0%
to 100% switch. Before applying power to a fixture,
check that the source voltage matches the fixture
’s
requirement. Check the fixture or device carefully to
make sure that if a voltage selection switch exists that it
is set to the correct line voltage you will use.
make sure that if a voltage selection switch exists that it
is set to the correct line voltage you will use.
Warning!
Verify that the internal multi-tap transformer
is set to match the line voltage applied. All
fixtures must be connected to circuits with a
suitable Earth Ground.
is set to match the line voltage applied. All
fixtures must be connected to circuits with a
suitable Earth Ground.
Safety Instructions
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
sell the unit to another user, be sure that they also receive
this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to
rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm (20in) from adjacent surfaces.
Be sure that no ventilation slots are blocked.
ventilation, at least 50cm (20in) from adjacent surfaces.
Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
replacing lamp or fuse and be sure to replace with same
lamp source.
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
Never carry the fixture solely by its head. Use its carrying
handles.
Maximum ambient temperature is Ta: 40
°
. Do not operate
fixture at temperatures higher than this.
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
Don
’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
Never disconnect power cord by pulling or tugging on the
cord.
cord.
Avoid direct eye exposure to lamp while it is on.
Caution!
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?